65 lines
2.3 KiB
C
65 lines
2.3 KiB
C
|
// Copyright 2022 xerootg
|
||
|
|
// SPDX-License-Identifier: GPL-2.0-or-later
|
||
|
|
|
||
|
|
#pragma once
|
||
|
|
|
||
|
|
#include "config_common.h"
|
||
|
|
|
||
|
|
/* USB Device descriptor parameter */
|
||
|
|
#undef DEVICE_VER
|
||
|
|
#define DEVICE_VER 0x0101 // added 1 for the rev1 + proton c
|
||
|
|
|
||
|
|
// wiring of each half
|
||
|
|
#undef MATRIX_ROW_PINS
|
||
|
|
#define MATRIX_ROW_PINS { B5, B3, B2, B1, B0 }
|
||
|
|
#undef MATRIX_COL_PINS
|
||
|
|
#define MATRIX_COL_PINS { A1, A0, B8, B13, B14, B15, B9 }
|
||
|
|
|
||
|
|
// //we are using hardware serial, so lets undef the softserial used otherwise
|
||
|
|
|
||
|
|
/* serial.c configuration for split keyboard */
|
||
|
|
#define SERIAL_USART_FULL_DUPLEX // Enable full duplex operation mode.
|
||
|
|
/*
|
||
|
|
Because the rev1 config defines SOFT_SERIAL_PIN, we need to undef it, redefine it, and also assign
|
||
|
|
it to avoid a redefine error.
|
||
|
|
*/
|
||
|
|
#undef SOFT_SERIAL_PIN
|
||
|
|
#define SOFT_SERIAL_PIN B6 // USART TX pin
|
||
|
|
|
||
|
|
#define SERIAL_USART_RX_PIN B7 // USART RX pin
|
||
|
|
#define SERIAL_USART_TX_PIN SOFT_SERIAL_PIN // USART TX pin
|
||
|
|
|
||
|
|
#define SERIAL_USART_PIN_SWAP // Swap TX and RX pins if keyboard is master halve.
|
||
|
|
// Check if this feature is necessary with your keyboard design and available on the mcu.
|
||
|
|
#define SELECT_SOFT_SERIAL_SPEED 1 // or 0, 2, 3, 4, 5
|
||
|
|
// 0: 460800 baud
|
||
|
|
// 1: 230400 baud (default)
|
||
|
|
// 2: 115200 baud
|
||
|
|
// 3: 57600 baud
|
||
|
|
// 4: 38400 baud
|
||
|
|
// 5: 19200 baud
|
||
|
|
#define SERIAL_USART_DRIVER SD1 // USART driver of TX and RX pin. default: SD1
|
||
|
|
#define SERIAL_USART_TX_PAL_MODE 7 // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 7
|
||
|
|
#define SERIAL_USART_RX_PAL_MODE 7 // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 7
|
||
|
|
#define SERIAL_USART_TIMEOUT 20 // USART driver timeout. default 20
|
||
|
|
|
||
|
|
/* ws2812 RGB LED */
|
||
|
|
#undef RGB_DI_PIN
|
||
|
|
#define RGB_DI_PIN A9
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Feature disable options
|
||
|
|
* These options are also useful to firmware size reduction.
|
||
|
|
*/
|
||
|
|
|
||
|
|
/* disable debug print */
|
||
|
|
// #define NO_DEBUG
|
||
|
|
|
||
|
|
/* disable print */
|
||
|
|
// #define NO_PRINT
|
||
|
|
|
||
|
|
/* disable action features */
|
||
|
|
//#define NO_ACTION_LAYER
|
||
|
|
//#define NO_ACTION_TAPPING
|
||
|
|
//#define NO_ACTION_ONESHOT
|