qmk_firmware/keyboards/ploopyco/mouse/readme.md

# Ploopyco Mouse

![Ploopyco Mouse](https://www.ploopy.co/uploads/1/2/7/6/127652558/s905404500980887952_p10_i19_w1414.jpeg)

It's a DIY, QMK Powered Trackball!!!!

Everything works. However the scroll wheel has some issues and acts very odd.

* Keyboard Maintainer: [PloopyCo](https://github.com/ploopyco), [Drashna Jael're](https://github.com/drashna/), [Germ](https://github.com/germ/)
* Hardware Supported: ATMega32u4 8MHz(3.3v)  
* Hardware Availability: [Store](https://ploopy.co), [GitHub](https://github.com/ploopyco)

Make example for this keyboard (after setting up your build environment):

    make ploopyco/mouse:default:flash
    
To jump to the bootloader, hold down "Button 4" (the "forward" button on the left side) 

See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

# Customzing your PloopyCo Trackball

While the defaults are designed so that it can be plugged in and used right away, there are a number of things that you may want to change.  Such as adding DPI control, or to use the ball to scroll while holding a button.   To allow for this sort of control, there is a callback for both the scroll wheel and the mouse censor. 

The default behavior for this is:

```c
void process_wheel_user(report_mouse_t* mouse_report, int16_t h, int16_t v) {
    mouse_report->h = h;
    mouse_report->v = v;
}

void process_mouse_user(report_mouse_t* mouse_report, int16_t x, int16_t y) {
    mouse_report->x = x;
    mouse_report->y = y;
}
```

This should allow you to more heavily customize the behavior. 

Alternatively, the `process_wheel` and `process_mouse` functions can both be replaced too, to allow for even more functionality.

Additionally, you can change the DPI/CPI or speed of the krackball by calling `pmw_set_cpi` at any time. Additionally, there is a `DPI_CONFIG` macro that will cycle through an array of options for the DPI.  This is set to 1200, 1600, and 2400, but can be changed.  1600 is also set to the default. 

To configure/set your own array, there are two defines to use, `PLOOPY_DPI_OPTIONS` to set the array, and `PLOOPY_DPI_DEFAULT`. 

```c
#define PLOOPY_DPI_OPTIONS { 1200, 1600, 2400 }
#define PLOOPY_DPI_DEFAULT 1
```
The `PLOOPY_DPI_OPTIONS` array sets the values that you want to be able to cycle through, and the order they are in.  The "default" define lets the firmware know which of these options is the default and should be loaded by default. 

The `DPI_CONFIG` macro will cycle through the values in the array, each time you hit it.  And it stores this value in persistent memory, so it will load it the next time the device powers up. 


# Programming QMK-DFU onto the PloopyCo Mouse

If you would rather have DFU on this board, you can use the QMK-DFU bootloader on the device.  To do so, you want to run: 

    make ploopyco/trackball:default:production

Once you have that, you'll need to [ISP Flash](https://docs.qmk.fm/#/isp_flashing_guide) the chip with the new bootloader hex file created (or the production hex), and set the fuses:


| Fuse     | Setting          |
|----------|------------------|
| Low      | `0xDF`           |
| High     | `0xD8` or `0x98` |
| Extended | `0xCB`           |

Original (Caterina) settings: 

| Fuse     | Setting          |
|----------|------------------|
| Low      | `0xFF`           |
| High     | `0xD8`           |
| Extended | `0xFE`           |