Nulo/qmk_firmware
1
0
Fork 0
Code Releases Activity

[Keyboard] Waldo RGB Enable (#6711)

Browse source 
* enable rgb animations

* clean up code
This commit is contained in:
MechMerlin 2019-09-09 21:57:45 -07:00 committed by Drashna Jaelre
parent 9dae7f7d85
commit 00225b77e5
2 changed files with 11 additions and 41 deletions
Show stats Download patch file Download diff file Expand all files Collapse all files

19
keyboards/waldo/config.h
View file

@ -36,16 +36,12 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
#define UNUSED_PINS
#define BACKLIGHT_PIN B7
#define BACKLIGHT_BREATHING
#define BACKLIGHT_LEVELS 3
/* COL2ROW or ROW2COL */
#define DIODE_DIRECTION COL2ROW
/* define if matrix has ghost */
//#define MATRIX_HAS_GHOST
/* number of backlight levels */
#define BACKLIGHT_LEVELS 3
/* Set 0 if debouncing isn't needed */
#define DEBOUNCE 5
@ -73,5 +69,12 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
//#define NO_ACTION_FUNCTION
// RGB LED
#define RGB_DI_PIN B0 // The pin the LED strip is connected to
#define RGBLED_NUM 10 // Number of LEDs in your strip
#define RGB_DI_PIN B0
#ifdef RGB_DI_PIN
#define RGBLIGHT_ANIMATIONS
#define RGBLED_NUM 10
#define RGBLIGHT_HUE_STEP 8
#define RGBLIGHT_SAT_STEP 8
#define RGBLIGHT_VAL_STEP 8
#define RGBLIGHT_SLEEP
#endif

33
keyboards/waldo/rules.mk
View file

@ -1,45 +1,12 @@
# MCU name
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Bootloader
# This definition is optional, and if your keyboard supports multiple bootloaders of
# different sizes, comment this out, and the correct address will be loaded
# automatically (+60). See bootloader.mk for all options.
BOOTLOADER = atmel-dfu
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT