Added basic support for JJ50 (preonic-like based on atmega32A) (#2546)
* Added support for JJ50 from KPRepublic, no rgb or backlight control yet. Added as a layout of ymd96 at the moment (same microprocessor). Basic keymap with three layers to get started. * Added support for JJ50
This commit is contained in:
parent
4adc333455
commit
00dfa73e4c
13 changed files with 1189 additions and 0 deletions
79
keyboards/jj50/README.md
Normal file
79
keyboards/jj50/README.md
Normal file
|
@ -0,0 +1,79 @@
|
|||
JJ50
|
||||
==========================
|
||||
|
||||
This is a port of the QMK firmware for boards that are based on the
|
||||
ps2avrGB firmware, like the [ps2avrGB keyboard] (https://www.keyclack.com/product/gb-ps2avrgb/), for use on the JJ50, a preonic-like board.
|
||||
|
||||
Most of the code was taken and amended from YMD96, which in itself was taken from ps2avrGB and amended by Andrew Novak.
|
||||
|
||||
Note that this is a complete replacement for the firmware, so you won't be
|
||||
using Bootmapper Client to change any keyboard settings, since not all the
|
||||
USB report options are supported.
|
||||
|
||||
Hardware Supported: JJ50 with the ATmega32a chip.
|
||||
Hardware Availability: The JJ50 PCB is available from kprepublic on AliExpress and suchlike.
|
||||
|
||||
|
||||
## Installing and Building
|
||||
|
||||
Make example for this keyboard (after setting up your build environment):
|
||||
|
||||
```
|
||||
$ make jj50:default:program
|
||||
```
|
||||
It should detect the keyboard and set it to bootloader mode automatically, prior to flashing firmware.
|
||||
|
||||
See [build environment setup](https://docs.qmk.fm/build_environment_setup.html) then the [make instructions](https://docs.qmk.fm/make_instructions.html) for more information.
|
||||
|
||||
Note that this is a complete replacement for the firmware, so you won't be
|
||||
using Bootmapper Client to change any keyboard settings, since not all the
|
||||
USB report options are supported.
|
||||
In addition you may need the AVR toolchain and `bootloadHID` for flashing:
|
||||
|
||||
```
|
||||
$ brew cask install crosspack-avr
|
||||
$ brew install --HEAD https://raw.githubusercontent.com/robertgzr/homebrew-tap/master/bootloadhid.rb
|
||||
```
|
||||
|
||||
In order to use the `./program` script, which can reboot the board into
|
||||
the bootloader, you'll need Python 2 with PyUSB installed:
|
||||
|
||||
```
|
||||
$ pip install pyusb
|
||||
```
|
||||
|
||||
If you prefer, you can just build it and flash the firmware directly with
|
||||
`bootloadHID` if you boot the board while holding down `Backspace` (`key below top right key`) to keep it
|
||||
in the bootloader:
|
||||
|
||||
```
|
||||
$ make jj50
|
||||
$ bootloadHID -r jj50_default.hex
|
||||
```
|
||||
I dont use windows personally, but the following is from ymd96 regarding flashing the atmega32a:
|
||||
|
||||
Since the JJ50 uses an ATmega32a chip instead of the 32u4, you need to download [HIDBootFlash v.1.0](http://vusb.wikidot.com/project:hidbootflash) for Windows. If anyone knows of a Linux/Mac bootflasher that works, edit this readme!
|
||||
On Windows, I use [MINGw](http://www.mingw.org/) to compile the keymaps. On Linux or OSX you can simply use the terminal.
|
||||
|
||||
Once you have those two pieces of software:
|
||||
Build the keyboard with
|
||||
```
|
||||
$ make jj50:default
|
||||
```
|
||||
If you make your own layout, change the `default` word to whatever your layout is.
|
||||
|
||||
And flash the compiled hex file with `HIDBootFlash`. Simply put the board in flashing mode by plugging it in while holding the key below the top right key, and click `find device`. Then you can specify the .hex file and flash it to the device.
|
||||
|
||||
|
||||
## Troubleshooting
|
||||
|
||||
1. Try plugging the board in while pressing `Backspace` (`Key below the top right key`). This will force it to boot only the bootloader without loading the firmware. Once this is done, just reflash the board with the original firmware.
|
||||
2. Sometimes USB hubs can act weird, so try connecting the board directly to your computer or plugging/unplugging the USB hub.
|
||||
3. If you get an error such as "Resource Unavailable" when attemting to flash on Linux, you may want to compile and run `tools/usb_detach.c`. See `tools/README.md` for more info.
|
||||
4. I was occasionally finding that I wasn't flashing changes that I was making to my keymap. If that happens, simply force rebuild by making with:
|
||||
```
|
||||
$ make -B jj50:default:program
|
||||
```
|
||||
|
||||
|
||||
|
54
keyboards/jj50/config.h
Normal file
54
keyboards/jj50/config.h
Normal file
|
@ -0,0 +1,54 @@
|
|||
/*
|
||||
Base Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
|
||||
Modified 2017 Andrew Novak <ndrw.nvk@gmail.com>
|
||||
Modified 2018 Wayne Jones (WarmCatUK) <waynekjones@gmail.com>
|
||||
|
||||
This program is free software: you can redistribute it and/or modify
|
||||
it under the terms of the GNU General Public License as published by
|
||||
the Free Software Foundation, either version 2 of the License, or
|
||||
(at your option) any later version.
|
||||
|
||||
This program is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
GNU General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU General Public License
|
||||
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
#ifndef CONFIG_H
|
||||
#define CONFIG_H
|
||||
|
||||
#include "config_common.h"
|
||||
|
||||
#define VENDOR_ID 0x20A0
|
||||
#define PRODUCT_ID 0x422D
|
||||
// TODO: share these strings with usbconfig.h
|
||||
// Edit usbconfig.h to change these.
|
||||
#define MANUFACTURER kprepublic
|
||||
#define PRODUCT jj50
|
||||
#define DESCRIPTION Preonic-like clone
|
||||
|
||||
/* matrix size */
|
||||
#define MATRIX_ROWS 8
|
||||
#define MATRIX_COLS 15
|
||||
#define DIODE_DIRECTION ROW2COL
|
||||
|
||||
#define BACKLIGHT_PIN D4
|
||||
#define BACKLIGHT_LEVELS 3
|
||||
|
||||
//#define RGB_DI_PIN C0
|
||||
#define RGBLED_NUM 5
|
||||
#define RGBLIGHT_ANIMATIONS
|
||||
#define RGBLIGHT_HUE_STEP 12
|
||||
#define RGBLIGHT_SAT_STEP 15
|
||||
#define RGBLIGHT_VAL_STEP 18
|
||||
|
||||
#define NO_UART 1
|
||||
#define BOOTLOADHID_BOOTLOADER 1
|
||||
|
||||
/* key combination for command */
|
||||
#define IS_COMMAND() (keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))
|
||||
|
||||
#endif
|
104
keyboards/jj50/i2c.c
Normal file
104
keyboards/jj50/i2c.c
Normal file
|
@ -0,0 +1,104 @@
|
|||
/*
|
||||
Copyright 2016 Luiz Ribeiro <luizribeiro@gmail.com>
|
||||
|
||||
This program is free software: you can redistribute it and/or modify
|
||||
it under the terms of the GNU General Public License as published by
|
||||
the Free Software Foundation, either version 2 of the License, or
|
||||
(at your option) any later version.
|
||||
|
||||
This program is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
GNU General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU General Public License
|
||||
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
#include <avr/io.h>
|
||||
#include <util/twi.h>
|
||||
|
||||
#include "i2c.h"
|
||||
|
||||
void i2c_set_bitrate(uint16_t bitrate_khz) {
|
||||
uint8_t bitrate_div = ((F_CPU / 1000l) / bitrate_khz);
|
||||
if (bitrate_div >= 16) {
|
||||
bitrate_div = (bitrate_div - 16) / 2;
|
||||
}
|
||||
TWBR = bitrate_div;
|
||||
}
|
||||
|
||||
void i2c_init(void) {
|
||||
// set pull-up resistors on I2C bus pins
|
||||
PORTC |= 0b11;
|
||||
|
||||
i2c_set_bitrate(400);
|
||||
|
||||
// enable TWI (two-wire interface)
|
||||
TWCR |= (1 << TWEN);
|
||||
|
||||
// enable TWI interrupt and slave address ACK
|
||||
TWCR |= (1 << TWIE);
|
||||
TWCR |= (1 << TWEA);
|
||||
}
|
||||
|
||||
uint8_t i2c_start(uint8_t address) {
|
||||
// reset TWI control register
|
||||
TWCR = 0;
|
||||
|
||||
// begin transmission and wait for it to end
|
||||
TWCR = (1<<TWINT) | (1<<TWSTA) | (1<<TWEN);
|
||||
while (!(TWCR & (1<<TWINT)));
|
||||
|
||||
// check if the start condition was successfully transmitted
|
||||
if ((TWSR & 0xF8) != TW_START) {
|
||||
return 1;
|
||||
}
|
||||
|
||||
// transmit address and wait
|
||||
TWDR = address;
|
||||
TWCR = (1<<TWINT) | (1<<TWEN);
|
||||
while (!(TWCR & (1<<TWINT)));
|
||||
|
||||
// check if the device has acknowledged the READ / WRITE mode
|
||||
uint8_t twst = TW_STATUS & 0xF8;
|
||||
if ((twst != TW_MT_SLA_ACK) && (twst != TW_MR_SLA_ACK)) {
|
||||
return 1;
|
||||
}
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
void i2c_stop(void) {
|
||||
TWCR = (1<<TWINT) | (1<<TWEN) | (1<<TWSTO);
|
||||
}
|
||||
|
||||
uint8_t i2c_write(uint8_t data) {
|
||||
TWDR = data;
|
||||
|
||||
// transmit data and wait
|
||||
TWCR = (1<<TWINT) | (1<<TWEN);
|
||||
while (!(TWCR & (1<<TWINT)));
|
||||
|
||||
if ((TWSR & 0xF8) != TW_MT_DATA_ACK) {
|
||||
return 1;
|
||||
}
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
uint8_t i2c_send(uint8_t address, uint8_t *data, uint16_t length) {
|
||||
if (i2c_start(address)) {
|
||||
return 1;
|
||||
}
|
||||
|
||||
for (uint16_t i = 0; i < length; i++) {
|
||||
if (i2c_write(data[i])) {
|
||||
return 1;
|
||||
}
|
||||
}
|
||||
|
||||
i2c_stop();
|
||||
|
||||
return 0;
|
||||
}
|
25
keyboards/jj50/i2c.h
Normal file
25
keyboards/jj50/i2c.h
Normal file
|
@ -0,0 +1,25 @@
|
|||
/*
|
||||
Copyright 2016 Luiz Ribeiro <luizribeiro@gmail.com>
|
||||
|
||||
This program is free software: you can redistribute it and/or modify
|
||||
it under the terms of the GNU General Public License as published by
|
||||
the Free Software Foundation, either version 2 of the License, or
|
||||
(at your option) any later version.
|
||||
|
||||
This program is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
GNU General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU General Public License
|
||||
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
#ifndef __I2C_H__
|
||||
#define __I2C_H__
|
||||
|
||||
void i2c_init(void);
|
||||
void i2c_set_bitrate(uint16_t bitrate_khz);
|
||||
uint8_t i2c_send(uint8_t address, uint8_t *data, uint16_t length);
|
||||
|
||||
#endif
|
45
keyboards/jj50/jj50.c
Normal file
45
keyboards/jj50/jj50.c
Normal file
|
@ -0,0 +1,45 @@
|
|||
/*
|
||||
Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
|
||||
|
||||
This program is free software: you can redistribute it and/or modify
|
||||
it under the terms of the GNU General Public License as published by
|
||||
the Free Software Foundation, either version 2 of the License, or
|
||||
(at your option) any later version.
|
||||
|
||||
This program is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
GNU General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU General Public License
|
||||
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
#include "jj50.h"
|
||||
#include "rgblight.h"
|
||||
|
||||
#include <avr/pgmspace.h>
|
||||
|
||||
#include "action_layer.h"
|
||||
#include "i2c.h"
|
||||
#include "quantum.h"
|
||||
|
||||
extern rgblight_config_t rgblight_config;
|
||||
|
||||
void rgblight_set(void) {
|
||||
if (!rgblight_config.enable) {
|
||||
for (uint8_t i = 0; i < RGBLED_NUM; i++) {
|
||||
led[i].r = 0;
|
||||
led[i].g = 0;
|
||||
led[i].b = 0;
|
||||
}
|
||||
}
|
||||
|
||||
i2c_init();
|
||||
i2c_send(0xb0, (uint8_t*)led, 3 * RGBLED_NUM);
|
||||
}
|
||||
|
||||
__attribute__ ((weak))
|
||||
void matrix_scan_user(void) {
|
||||
rgblight_task();
|
||||
}
|
50
keyboards/jj50/jj50.h
Normal file
50
keyboards/jj50/jj50.h
Normal file
|
@ -0,0 +1,50 @@
|
|||
/*
|
||||
Base Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
|
||||
Modified 2017 Andrew Novak <ndrw.nvk@gmail.com>
|
||||
Modified 2018 Wayne Jones (WarmCatUK) <waynekjones@gmail.com>
|
||||
|
||||
This program is free software: you can redistribute it and/or modify
|
||||
it under the terms of the GNU General Public License as published by
|
||||
the Free Software Foundation, either version 2 of the License, or
|
||||
(at your option) any later version.
|
||||
|
||||
This program is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
GNU General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU General Public License
|
||||
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
#ifndef KEYMAP_COMMON_H
|
||||
#define KEYMAP_COMMON_H
|
||||
|
||||
#include "quantum_keycodes.h"
|
||||
#include "keycode.h"
|
||||
#include "action.h"
|
||||
|
||||
#define KEYMAP( \
|
||||
K011, K010, K009, K008, K004, K005, K006, K007, K003, K002, K201, K000, \
|
||||
K111, K110, K109, K108, K104, K105, K106, K107, K103, K102, K001, K100, \
|
||||
K211, K210, K209, K208, K204, K205, K206, K207, K203, K202, K101, K200, \
|
||||
K311, K310, K309, K308, K304, K305, K306, K307, K303, K302, K301, K300, \
|
||||
K411, K410, K409, K408, K404, K405, K406, K407, K403, K402, K401, K400 \
|
||||
) { \
|
||||
{ K100, K001, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, }, \
|
||||
{ K200, K101, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, }, \
|
||||
{ K000, K201, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, }, \
|
||||
{ K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, }, \
|
||||
{ K400, K401, K402, K403, K404, K405, K406, K407, K408, K409, K410, K411 }, \
|
||||
}
|
||||
|
||||
#endif
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
|
96
keyboards/jj50/keymaps/default/keymap.c
Normal file
96
keyboards/jj50/keymaps/default/keymap.c
Normal file
|
@ -0,0 +1,96 @@
|
|||
/*
|
||||
Base Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
|
||||
Modified 2017 Andrew Novak <ndrw.nvk@gmail.com>
|
||||
Modified 2018 Wayne Jones (WarmCatUK) <waynekjones@gmail.com>
|
||||
|
||||
This program is free software: you can redistribute it and/or modify
|
||||
it under the terms of the GNU General Public License as published by
|
||||
the Free Software Foundation, either version 2 of the License, or
|
||||
(at your option) any later version.
|
||||
|
||||
This program is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
GNU General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU General Public LicensezZZ
|
||||
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
#include "jj50.h"
|
||||
#include "action_layer.h"
|
||||
#include "rgblight.h"
|
||||
|
||||
#define ______ KC_TRNS
|
||||
#define _DEFLT 0
|
||||
#define _RAISE 1
|
||||
#define _LOWER 2
|
||||
|
||||
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
|
||||
|
||||
/* Qwerty
|
||||
* ,-----------------------------------------------------------------------------------.
|
||||
* | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | - | = |
|
||||
* |------+------+------+------+------+------+------+------+------+------+------+------|
|
||||
* | Tab | Q | W | E | R | T | Y | U | I | O | P | Bksp |
|
||||
* |------+------+------+------+------+------+------+------+------+------+------+------|
|
||||
* | Esc | A | S | D | F | G | H | J | K | L | ; | " |
|
||||
* |------+------+------+------+------+------+------+------+------+------+------+------|
|
||||
* | Shift| Z | X | C | V | B | N | M | , | . | / |Enter |
|
||||
* |------+------+------+------+------+------+------+------+------+------+------+------|
|
||||
* | | Ctrl | Alt | GUI |Lower | Space |Raise | Left | Down | Up |Right |
|
||||
* `-----------------------------------------------------------------------------------'
|
||||
*/
|
||||
[_DEFLT] = KEYMAP( \
|
||||
KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, \
|
||||
KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC, \
|
||||
KC_ESC, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, \
|
||||
KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, SFT_T(KC_ENT),\
|
||||
BL_TOGG, KC_LCTL, KC_LALT, KC_LGUI, MO(_LOWER), KC_SPC,KC_SPC, MO(_RAISE),KC_LEFT, KC_DOWN, KC_UP, KC_RGHT \
|
||||
),
|
||||
|
||||
|
||||
/* Raise
|
||||
* ,-----------------------------------------------------------------------------------.
|
||||
* | F1 | F2 | F3 | F4 | F5 | F6 | F7 | F8 | F9 | F10 | F11 | F12 |
|
||||
* |------+------+------+------+------+------+------+------+------+------+------+------|
|
||||
* | ` | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | Del |
|
||||
* |------+------+------+------+------+------+------+------+------+------+------+------|
|
||||
* | | | | | | | | | | [ | ] | \ |
|
||||
* |------+------+------+------+------+------+------+------+------+------+------+------|
|
||||
* | | | | | | | |ISO # |ISO / | PUP | PDN | |
|
||||
* |------+------+------+------+------+------+------+------+------+------+------+------|
|
||||
* | | | | | | | | Next | Vol- | Vol+ | Play |
|
||||
* `-----------------------------------------------------------------------------------'
|
||||
*/
|
||||
[_RAISE] = KEYMAP( \
|
||||
KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, \
|
||||
KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_DEL, \
|
||||
RESET, BL_INC, RGB_SAI, _______, _______, _______, _______, _______, _______, KC_LBRC, KC_RBRC, KC_BSLS, \
|
||||
_______, BL_DEC, _______, _______, _______, _______, _______, KC_NUHS, KC_NUBS, KC_PGUP, KC_PGDN, _______, \
|
||||
RGB_TOG, _______, _______, _______, _______, _______, _______, _______, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY \
|
||||
),
|
||||
|
||||
|
||||
/* Lower
|
||||
* ,-----------------------------------------------------------------------------------.
|
||||
* | F1 | F2 | F3 | F4 | F5 | F6 | F7 | F8 | F9 | F10 | F11 | F12 |
|
||||
* |------+------+------+------+------+------+------+------+------+------+------+------|
|
||||
* | ~ | ! | @ | # | $ | % | ^ | & | * | ( | ) | Del |
|
||||
* |------+------+------+------+------+------+------+------+------+------+------+------|
|
||||
* | | | | | | | | | | { | } | | |
|
||||
* |------+------+------+------+------+------+------+------+------+------+------+------|
|
||||
* | | | | | | | |ISO ~ |ISO | | HOM | END | |
|
||||
* |------+------+------+------+------+------+------+------+------+------+------+------|
|
||||
* | | | | | | | | Next | Vol- | Vol+ | Play |
|
||||
* `-----------------------------------------------------------------------------------'
|
||||
*/
|
||||
[_LOWER] = KEYMAP( \
|
||||
KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, \
|
||||
KC_TILD, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_DEL, \
|
||||
RESET, _______, _______, _______, _______, _______, _______, _______, _______, KC_LCBR, KC_RCBR, KC_PIPE, \
|
||||
_______, _______, _______, _______, _______, _______, _______,S(KC_NUHS),S(KC_NUBS),KC_HOME, KC_END, _______, \
|
||||
_______, _______, _______, _______, _______, _______, _______, _______, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY \
|
||||
)
|
||||
|
||||
};
|
106
keyboards/jj50/matrix.c
Normal file
106
keyboards/jj50/matrix.c
Normal file
|
@ -0,0 +1,106 @@
|
|||
/*
|
||||
Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
|
||||
|
||||
This program is free software: you can redistribute it and/or modify
|
||||
it under the terms of the GNU General Public License as published by
|
||||
the Free Software Foundation, either version 2 of the License, or
|
||||
(at your option) any later version.
|
||||
|
||||
This program is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
GNU General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU General Public License
|
||||
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
#include <avr/io.h>
|
||||
#include <util/delay.h>
|
||||
|
||||
#include "matrix.h"
|
||||
|
||||
#ifndef DEBOUNCE
|
||||
# define DEBOUNCE 5
|
||||
#endif
|
||||
|
||||
static uint8_t debouncing = DEBOUNCE;
|
||||
|
||||
static matrix_row_t matrix[MATRIX_ROWS];
|
||||
static matrix_row_t matrix_debouncing[MATRIX_ROWS];
|
||||
|
||||
void matrix_init(void) {
|
||||
// all outputs for rows high
|
||||
DDRB = 0xFF;
|
||||
PORTB = 0xFF;
|
||||
// all inputs for columns
|
||||
DDRA = 0x00;
|
||||
DDRC &= ~(0x111111<<2);
|
||||
DDRD &= ~(1<<PIND7);
|
||||
// all columns are pulled-up
|
||||
PORTA = 0xFF;
|
||||
PORTC |= (0b111111<<2);
|
||||
//PORTD |= (1<<PIND7);
|
||||
|
||||
// initialize matrix state: all keys off
|
||||
for (uint8_t row = 0; row < MATRIX_ROWS; row++) {
|
||||
matrix[row] = 0x00;
|
||||
matrix_debouncing[row] = 0x00;
|
||||
}
|
||||
}
|
||||
|
||||
void matrix_set_row_status(uint8_t row) {
|
||||
DDRB = (1 << row);
|
||||
PORTB = ~(1 << row);
|
||||
}
|
||||
|
||||
uint8_t bit_reverse(uint8_t x) {
|
||||
x = ((x >> 1) & 0x55) | ((x << 1) & 0xaa);
|
||||
x = ((x >> 2) & 0x33) | ((x << 2) & 0xcc);
|
||||
x = ((x >> 4) & 0x0f) | ((x << 4) & 0xf0);
|
||||
return x;
|
||||
}
|
||||
|
||||
uint8_t matrix_scan(void) {
|
||||
for (uint8_t row = 0; row < MATRIX_ROWS; row++) {
|
||||
matrix_set_row_status(row);
|
||||
_delay_us(5);
|
||||
|
||||
matrix_row_t cols = (
|
||||
// cols 0..7, PORTA 0 -> 7
|
||||
(~PINA) & 0xFF
|
||||
) | (
|
||||
// cols 8..13, PORTC 7 -> 0
|
||||
bit_reverse((~PINC) & 0xFF) << 8
|
||||
) | (
|
||||
// col 14, PORTD 7
|
||||
((~PIND) & (1 << PIND7)) << 7
|
||||
);
|
||||
|
||||
if (matrix_debouncing[row] != cols) {
|
||||
matrix_debouncing[row] = cols;
|
||||
debouncing = DEBOUNCE;
|
||||
}
|
||||
}
|
||||
|
||||
if (debouncing) {
|
||||
if (--debouncing) {
|
||||
_delay_ms(1);
|
||||
} else {
|
||||
for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
|
||||
matrix[i] = matrix_debouncing[i];
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
matrix_scan_user();
|
||||
|
||||
return 1;
|
||||
}
|
||||
|
||||
inline matrix_row_t matrix_get_row(uint8_t row) {
|
||||
return matrix[row];
|
||||
}
|
||||
|
||||
void matrix_print(void) {
|
||||
}
|
74
keyboards/jj50/program
Normal file
74
keyboards/jj50/program
Normal file
|
@ -0,0 +1,74 @@
|
|||
#!/usr/bin/env python
|
||||
# Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
|
||||
#
|
||||
# This program is free software: you can redistribute it and/or modify
|
||||
# it under the terms of the GNU General Public License as published by
|
||||
# the Free Software Foundation, either version 2 of the License, or
|
||||
# (at your option) any later version.
|
||||
#
|
||||
# This program is distributed in the hope that it will be useful,
|
||||
# but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
# GNU General Public License for more details.
|
||||
#
|
||||
# You should have received a copy of the GNU General Public License
|
||||
# along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
|
||||
from __future__ import print_function
|
||||
|
||||
import os
|
||||
import sys
|
||||
import time
|
||||
import usb
|
||||
|
||||
if len(sys.argv) < 2:
|
||||
print('Usage: %s <firmware.hex>' % sys.argv[0])
|
||||
sys.exit(1)
|
||||
|
||||
print('Searching for ps2avrGB... ', end='')
|
||||
|
||||
dev = usb.core.find(idVendor=0x20A0, idProduct=0x422D)
|
||||
if dev is None:
|
||||
raise ValueError('Device not found')
|
||||
|
||||
print('Found', end='\n\n')
|
||||
|
||||
print('Device Information:')
|
||||
print(' idVendor: %d (0x%04x)' % (dev.idVendor, dev.idVendor))
|
||||
print(' idProduct: %d (0x%04x)' % (dev.idProduct, dev.idProduct))
|
||||
print('Manufacturer: %s' % (dev.iManufacturer))
|
||||
print('Serial: %s' % (dev.iSerialNumber))
|
||||
print('Product: %s' % (dev.iProduct), end='\n\n')
|
||||
|
||||
print('Transferring control to bootloader... ', end='')
|
||||
|
||||
dev.set_configuration()
|
||||
|
||||
request_type = usb.util.build_request_type(
|
||||
usb.util.CTRL_OUT,
|
||||
usb.util.CTRL_TYPE_CLASS,
|
||||
usb.util.CTRL_RECIPIENT_DEVICE)
|
||||
|
||||
USBRQ_HID_SET_REPORT = 0x09
|
||||
HID_REPORT_OPTION = 0x0301
|
||||
|
||||
|
||||
try:
|
||||
dev.ctrl_transfer(
|
||||
request_type,
|
||||
USBRQ_HID_SET_REPORT,
|
||||
HID_REPORT_OPTION,
|
||||
0,
|
||||
[0, 0, 0xFF] + [0] * 5
|
||||
)
|
||||
except usb.core.USBError:
|
||||
# for some reason I keep getting USBError, but it works!
|
||||
pass
|
||||
|
||||
# wait a bit until bootloader starts up
|
||||
time.sleep(2)
|
||||
|
||||
print('OK')
|
||||
print('Programming...')
|
||||
if os.system('bootloadHID -r "%s"' % sys.argv[1]) == 0:
|
||||
print('\nDone!')
|
51
keyboards/jj50/rules.mk
Normal file
51
keyboards/jj50/rules.mk
Normal file
|
@ -0,0 +1,51 @@
|
|||
# Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
|
||||
# Modified 2018 Wayne Jones (WarmCatUK) <waynekjones@gmail.com>
|
||||
|
||||
# This program is free software: you can redistribute it and/or modify
|
||||
# it under the terms of the GNU General Public License as published by
|
||||
# the Free Software Foundation, either version 2 of the License, or
|
||||
# (at your option) any later version.
|
||||
#
|
||||
# This program is distributed in the hope that it will be useful,
|
||||
# but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
# GNU General Public License for more details.
|
||||
#
|
||||
# You should have received a copy of the GNU General Public License
|
||||
# along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
|
||||
# MCU name
|
||||
MCU = atmega32a
|
||||
PROTOCOL = VUSB
|
||||
|
||||
# unsupported features for now
|
||||
NO_UART = yes
|
||||
NO_SUSPEND_POWER_DOWN = yes
|
||||
|
||||
# processor frequency
|
||||
F_CPU = 12000000
|
||||
|
||||
# Bootloader
|
||||
# This definition is optional, and if your keyboard supports multiple bootloaders of
|
||||
# different sizes, comment this out, and the correct address will be loaded
|
||||
# automatically (+60). See bootloader.mk for all options.
|
||||
BOOTLOADER = bootloadHID
|
||||
|
||||
# build options
|
||||
BOOTMAGIC_ENABLE = yes
|
||||
MOUSEKEY_ENABLE = no
|
||||
EXTRAKEY_ENABLE = yes
|
||||
CONSOLE_ENABLE = no
|
||||
COMMAND_ENABLE = no
|
||||
BACKLIGHT_ENABLE = yes
|
||||
RGBLIGHT_ENABLE = yes
|
||||
RGBLIGHT_CUSTOM_DRIVER = yes
|
||||
|
||||
OPT_DEFS = -DDEBUG_LEVEL=0
|
||||
|
||||
# custom matrix setup
|
||||
CUSTOM_MATRIX = yes
|
||||
SRC = matrix.c i2c.c
|
||||
|
||||
# programming options
|
||||
PROGRAM_CMD = ./keyboards/ps2avrGB/program $(TARGET).hex
|
396
keyboards/jj50/usbconfig.h
Normal file
396
keyboards/jj50/usbconfig.h
Normal file
|
@ -0,0 +1,396 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#ifndef __usbconfig_h_included__
|
||||
#define __usbconfig_h_included__
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_INTR_POLL_INTERVAL 1
|
||||
/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
|
||||
* interval. The value is in milliseconds and must not be less than 10 ms for
|
||||
* low speed devices.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_MAX_BUS_POWER 500
|
||||
/* Set this variable to the maximum USB bus power consumption of your device.
|
||||
* The value is in milliamperes. [It will be divided by two since USB
|
||||
* communicates power requirements in units of 2 mA.]
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID (VENDOR_ID & 0xFF), ((VENDOR_ID >> 8) & 0xFF)
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID (PRODUCT_ID & 0xFF), ((PRODUCT_ID >> 8) & 0xFF)
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_VERSION 0x00, 0x02
|
||||
/* Version number of the device: Minor number first, then major number.
|
||||
*/
|
||||
#define USB_CFG_VENDOR_NAME 'w', 'i', 'n', 'k', 'e', 'y', 'l', 'e', 's', 's', '.', 'k', 'r'
|
||||
#define USB_CFG_VENDOR_NAME_LEN 13
|
||||
/* These two values define the vendor name returned by the USB device. The name
|
||||
* must be given as a list of characters under single quotes. The characters
|
||||
* are interpreted as Unicode (UTF-16) entities.
|
||||
* If you don't want a vendor name string, undefine these macros.
|
||||
* ALWAYS define a vendor name containing your Internet domain name if you use
|
||||
* obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for
|
||||
* details.
|
||||
*/
|
||||
#define USB_CFG_DEVICE_NAME 'p', 's', '2', 'a', 'v', 'r', 'G', 'B'
|
||||
#define USB_CFG_DEVICE_NAME_LEN 8
|
||||
/* Same as above for the device name. If you don't want a device name, undefine
|
||||
* the macros. See the file USB-IDs-for-free.txt before you assign a name if
|
||||
* you use a shared VID/PID.
|
||||
*/
|
||||
/*#define USB_CFG_SERIAL_NUMBER 'N', 'o', 'n', 'e' */
|
||||
/*#define USB_CFG_SERIAL_NUMBER_LEN 0 */
|
||||
/* Same as above for the serial number. If you don't want a serial number,
|
||||
* undefine the macros.
|
||||
* It may be useful to provide the serial number through other means than at
|
||||
* compile time. See the section about descriptor properties below for how
|
||||
* to fine tune control over USB descriptors such as the string descriptor
|
||||
* for the serial number.
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE 0
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
//#define USB_CFG_DESCR_PROPS_CONFIGURATION 0
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS 0
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 0
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR 0
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT 0
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER 0
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
//#define USB_CFG_DESCR_PROPS_HID 0
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
//#define USB_CFG_DESCR_PROPS_HID_REPORT 0
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
||||
#endif /* __usbconfig_h_included__ */
|
96
keyboards/ymd96/keymaps/JJ50/keymap.c
Normal file
96
keyboards/ymd96/keymaps/JJ50/keymap.c
Normal file
|
@ -0,0 +1,96 @@
|
|||
/*
|
||||
Base Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
|
||||
Modified 2017 Andrew Novak <ndrw.nvk@gmail.com>
|
||||
Modified 2018 Wayne Jones (WarmCatUK) <waynekjones@gmail.com>
|
||||
|
||||
This program is free software: you can redistribute it and/or modify
|
||||
it under the terms of the GNU General Public License as published by
|
||||
the Free Software Foundation, either version 2 of the License, or
|
||||
(at your option) any later version.
|
||||
|
||||
This program is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
GNU General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU General Public LicensezZZ
|
||||
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
#include "ymd96.h"
|
||||
#include "action_layer.h"
|
||||
#include "rgblight.h"
|
||||
|
||||
#define ______ KC_TRNS
|
||||
#define _DEFLT 0
|
||||
#define _RAISE 1
|
||||
#define _LOWER 2
|
||||
|
||||
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
|
||||
|
||||
/* Qwerty
|
||||
* ,-----------------------------------------------------------------------------------.
|
||||
* | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | - | = |
|
||||
* |------+------+------+------+------+------+------+------+------+------+------+------|
|
||||
* | Tab | Q | W | E | R | T | Y | U | I | O | P | Bksp |
|
||||
* |------+------+------+------+------+------+------+------+------+------+------+------|
|
||||
* | Esc | A | S | D | F | G | H | J | K | L | ; | " |
|
||||
* |------+------+------+------+------+------+------+------+------+------+------+------|
|
||||
* | Shift| Z | X | C | V | B | N | M | , | . | / |Enter |
|
||||
* |------+------+------+------+------+------+------+------+------+------+------+------|
|
||||
* | | Ctrl | Alt | GUI |Lower | Space |Raise | Left | Down | Up |Right |
|
||||
* `-----------------------------------------------------------------------------------'
|
||||
*/
|
||||
[_DEFLT] = KEYMAP_JJ50( \
|
||||
KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, \
|
||||
KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC, \
|
||||
KC_ESC, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, \
|
||||
KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, SFT_T(KC_ENT),\
|
||||
_______, KC_LCTL, KC_LALT, KC_LGUI, MO(_LOWER), KC_SPC,KC_SPC, MO(_RAISE),KC_LEFT, KC_DOWN, KC_UP, KC_RGHT \
|
||||
),
|
||||
|
||||
|
||||
/* Raise
|
||||
* ,-----------------------------------------------------------------------------------.
|
||||
* | F1 | F2 | F3 | F4 | F5 | F6 | F7 | F8 | F9 | F10 | F11 | F12 |
|
||||
* |------+------+------+------+------+------+------+------+------+------+------+------|
|
||||
* | ` | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | Del |
|
||||
* |------+------+------+------+------+------+------+------+------+------+------+------|
|
||||
* | | | | | | | | | | [ | ] | \ |
|
||||
* |------+------+------+------+------+------+------+------+------+------+------+------|
|
||||
* | | | | | | | |ISO # |ISO / | PUP | PDN | |
|
||||
* |------+------+------+------+------+------+------+------+------+------+------+------|
|
||||
* | | | | | | | | Next | Vol- | Vol+ | Play |
|
||||
* `-----------------------------------------------------------------------------------'
|
||||
*/
|
||||
[_RAISE] = KEYMAP_JJ50( \
|
||||
KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, \
|
||||
KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_DEL, \
|
||||
_______, _______, _______, _______, _______, _______, _______, _______, _______, KC_LBRC, KC_RBRC, KC_BSLS, \
|
||||
_______, _______, _______, _______, _______, _______, _______, KC_NUHS, KC_NUBS, KC_PGUP, KC_PGDN, _______, \
|
||||
_______, _______, _______, _______, _______, _______, _______, _______, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY \
|
||||
),
|
||||
|
||||
|
||||
/* Lower
|
||||
* ,-----------------------------------------------------------------------------------.
|
||||
* | F1 | F2 | F3 | F4 | F5 | F6 | F7 | F8 | F9 | F10 | F11 | F12 |
|
||||
* |------+------+------+------+------+------+------+------+------+------+------+------|
|
||||
* | ~ | ! | @ | # | $ | % | ^ | & | * | ( | ) | Del |
|
||||
* |------+------+------+------+------+------+------+------+------+------+------+------|
|
||||
* | | | | | | | | | | { | } | | |
|
||||
* |------+------+------+------+------+------+------+------+------+------+------+------|
|
||||
* | | | | | | | |ISO ~ |ISO | | HOM | END | |
|
||||
* |------+------+------+------+------+------+------+------+------+------+------+------|
|
||||
* | | | | | | | | Next | Vol- | Vol+ | Play |
|
||||
* `-----------------------------------------------------------------------------------'
|
||||
*/
|
||||
[_LOWER] = KEYMAP_JJ50( \
|
||||
KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, \
|
||||
KC_TILD, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_DEL, \
|
||||
_______, _______, _______, _______, _______, _______, _______, _______, _______, KC_LCBR, KC_RCBR, KC_PIPE, \
|
||||
_______, _______, _______, _______, _______, _______, _______,S(KC_NUHS),S(KC_NUBS),KC_HOME, KC_END, _______, \
|
||||
_______, _______, _______, _______, _______, _______, _______, _______, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY \
|
||||
)
|
||||
|
||||
};
|
|
@ -41,6 +41,19 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|||
{ K700, K701, K702, K703, K704, K705, K706, KC_NO, K708, K709, K710, K711, K712, K713, K714 } \
|
||||
}
|
||||
|
||||
#define KEYMAP_JJ50( \
|
||||
K011, K010, K009, K008, K004, K005, K006, K007, K003, K002, K201, K000, \
|
||||
K111, K110, K109, K108, K104, K105, K106, K107, K103, K102, K001, K100, \
|
||||
K211, K210, K209, K208, K204, K205, K206, K207, K203, K202, K101, K200, \
|
||||
K311, K310, K309, K308, K304, K305, K306, K307, K303, K302, K301, K300, \
|
||||
K411, K410, K409, K408, K404, K405, K406, K407, K403, K402, K401, K400 \
|
||||
) { \
|
||||
{ K100, K001, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, }, \
|
||||
{ K200, K101, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, }, \
|
||||
{ K000, K201, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, }, \
|
||||
{ K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, }, \
|
||||
{ K400, K401, K402, K403, K404, K405, K406, K407, K408, K409, K410, K411 }, \
|
||||
}
|
||||
|
||||
|
||||
#endif
|
||||
|
|
Loading…
Reference in a new issue