diff --git a/keyboard/phantom/Makefile b/keyboard/phantom/Makefile
new file mode 100644
index 0000000000..0fbcf914fd
--- /dev/null
+++ b/keyboard/phantom/Makefile
@@ -0,0 +1,112 @@
+#----------------------------------------------------------------------------
+# On command line:
+#
+# make all = Make software.
+#
+# make clean = Clean out built project files.
+#
+# make coff = Convert ELF to AVR COFF.
+#
+# make extcoff = Convert ELF to AVR Extended COFF.
+#
+# make program = Download the hex file to the device.
+#                Please customize your programmer settings(PROGRAM_CMD)
+#
+# make teensy = Download the hex file to the device, using teensy_loader_cli.
+#               (must have teensy_loader_cli installed).
+#
+# make dfu = Download the hex file to the device, using dfu-programmer (must
+#            have dfu-programmer installed).
+#
+# make flip = Download the hex file to the device, using Atmel FLIP (must
+#             have Atmel FLIP installed).
+#
+# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
+#               (must have dfu-programmer installed).
+#
+# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
+#                (must have Atmel FLIP installed).
+#
+# make debug = Start either simulavr or avarice as specified for debugging,
+#              with avr-gdb or avr-insight as the front end for debugging.
+#
+# make filename.s = Just compile filename.c into the assembler code only.
+#
+# make filename.i = Create a preprocessed source file for use in submitting
+#                   bug reports to the GCC project.
+#
+# To rebuild project do "make clean" then "make all".
+#----------------------------------------------------------------------------
+
+SRC = led.c
+
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   comment out to disable the options.
+#
+BOOTMAGIC_ENABLE ?= yes	# Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= no	# Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes	# Audio control and System control(+450)
+CONSOLE_ENABLE ?= yes	# Console for debug(+400)
+COMMAND_ENABLE ?= yes    # Commands for debug and configuration
+NKRO_ENABLE ?= yes		# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+RGBLIGHT_ENABLE ?=yes   # Enable keyboard underlight functionality (+4870)
+BACKLIGHT_ENABLE ?= no  # Enable keyboard backlight functionality (+1150)
+MIDI_ENABLE ?= no 		# MIDI controls
+AUDIO_ENABLE ?= no
+UNICODE_ENABLE ?= no 		# Unicode
+BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
+
+
+ifndef QUANTUM_DIR
+	include ../../Makefile
+endif
diff --git a/keyboard/phantom/config.h b/keyboard/phantom/config.h
new file mode 100644
index 0000000000..d5878766f0
--- /dev/null
+++ b/keyboard/phantom/config.h
@@ -0,0 +1,91 @@
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x6060
+#define DEVICE_VER      0x0003
+#define MANUFACTURER    PHANTOM
+#define PRODUCT         PHANTOM RGB MOD
+#define DESCRIPTION     QMK keyboard firmware for PHANTOM TKL
+
+/* key matrix size */
+#define MATRIX_ROWS 6
+#define MATRIX_COLS 17
+
+// ROWS: Top to bottom, COLS: Left to right
+/* Row pin configuration
+*/
+#define MATRIX_ROW_PINS { B5, B4, B3, B2, B1, B0 }
+/* Column pin configuration
+ */
+#define MATRIX_COL_PINS { D5, C7, C6, D4, D0, E6, F0, F1, F4, F5, F6, F7, D7, D6, D1, D2, D3 }
+#define UNUSED_PINS
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION ROW2COL
+
+/* define if matrix has ghost */
+//#define MATRIX_HAS_GHOST
+
+/* Set 0 if debouncing isn't needed */
+#define DEBOUNCING_DELAY 5
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* key combination for command */
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/* Underlight configuration
+ */
+ #define ws2812_PORTREG PORTE
+ #define ws2812_DDRREG DDRE
+ #define ws2812_pin 2
+ #define RGBLED_NUM 20     // Number of LEDs
+ #define RGBLIGHT_HUE_STEP 10
+ #define RGBLIGHT_SAT_STEP 17
+ #define RGBLIGHT_VAL_STEP 17
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+#endif
diff --git a/keyboard/phantom/keymaps/default/compiled.hex b/keyboard/phantom/keymaps/default/compiled.hex
new file mode 100644
index 0000000000..37bbfb5551
Binary files /dev/null and b/keyboard/phantom/keymaps/default/compiled.hex differ
diff --git a/keyboard/phantom/keymaps/default/keymap.c b/keyboard/phantom/keymaps/default/keymap.c
new file mode 100644
index 0000000000..1368226aa9
--- /dev/null
+++ b/keyboard/phantom/keymaps/default/keymap.c
@@ -0,0 +1,169 @@
+#include "phantom.h"
+
+#ifdef RGBLIGHT_ENABLE
+#include "rgblight.h"
+#endif
+
+// Used for SHIFT_ESC
+#define MODS_CTRL_MASK  (MOD_BIT(KC_LSHIFT)|MOD_BIT(KC_RSHIFT))
+
+// Each layer gets a name for readability, which is then used in the keymap matrix below.
+// The underscores don't mean anything - you can have a layer called STUFF or any other name.
+// Layer names don't all need to be of the same length, obviously, and you can also skip them
+// entirely and just use numbers.
+#define _BL 0
+#define _FL 1
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+  /* Keymap _BL: (Base Layer) Default Layer
+   * ,-----------------------------------------------------------------------------.
+   * |Esc  |f1| f2| f3| f4|  | f5| f6| f7| f8|   | f9|f10|f11|f12|	|Prnt|ScLk|Paus|
+   * |-----------------------------------------------------------|	|--------------|
+   * | ~ | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 |  0| - | = |Backsp |	| Ins|Home|PgUp|
+   * |-----------------------------------------------------------|	|--------------|
+   * |Tab  |  Q|  W|  E|  R|  T|  Y|  U|  I|  O|  P|  [|  ]|    \|	| Del| End|PgDn|
+   * |-----------------------------------------------------------|	`--------------'
+   * |CAPS   |  A|  S|  D|  F|  G|  H|  J|  K|  L|  ;|  '|Return |
+   * |-----------------------------------------------------------|		 ,----.
+   * |Shift   |  Z|  X|  C|  V|  B|  N|  M|  ,|  .|  /|Shift     |		 | Up |
+   * |-----------------------------------------------------------|	 ,-------------.
+   * |Ctrl|Gui |Alt |      Space            |ALT |GUI |_FL |CTRL |	 |Lft| Dn |Rig |
+   * `-----------------------------------------------------------'	 `-------------'
+   */
+[_BL] = KEYMAP(
+  KC_ESC, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_PSCR, KC_SLCK, KC_PAUS, \
+  KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, KC_INS, KC_HOME, KC_PGUP, \
+  KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, KC_DELETE, KC_END, KC_PGDN, \
+  KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT,  \
+  KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, KC_UP, \
+  KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_RALT, KC_RGUI, MO(_FL), KC_RCTL, KC_LEFT, KC_DOWN, KC_RGHT),
+
+  /* Keymap _FL: Function Layer
+   * ,-----------------------------------------------------------------------------.
+   * |     |  |   |   |   |  |   |   |   |   |   |   |   |   |   |	|    |    |    |
+   * |-----------------------------------------------------------|	|--------------|
+   * |   |   |   |   |   |   |   |   |   |   |   |   |   | Reset |	|    |    |    |
+   * |-----------------------------------------------------------|	|--------------|
+   * |     |   |   |   |   |   |   |   |   |   |   |   |   |     |	|    |    |    |
+   * |-----------------------------------------------------------|	`--------------'
+   * |       |   |   |   |   |   |   |   |   |   |   |   |       |
+   * |-----------------------------------------------------------|		 ,----.
+   * |        | F1| F2| F3| F4| F5|F6 |F7 |F8 |   |   |          |		 |    |
+   * |-----------------------------------------------------------|	 ,-------------.
+   * |    |    |    |                       |    |    |    |     |	 |   |    |    |
+   * `-----------------------------------------------------------'	 `-------------'
+   */
+[_FL] = KEYMAP(
+  #ifdef RGBLIGHT_ENABLE
+  KC_TRNS,  KC_TRNS, KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS, KC_TRNS, KC_TRNS, \
+  KC_TRNS,  KC_TRNS, KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS, KC_TRNS, KC_TRNS, RESET, KC_TRNS, KC_TRNS, KC_TRNS, \
+  KC_TRNS,  KC_TRNS, KC_TRNS,  KC_TRNS, KC_TRNS,  KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \
+  KC_TRNS,  KC_TRNS, KC_TRNS,  KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,   KC_TRNS,  KC_TRNS, KC_UP, KC_TRNS, \
+  KC_TRNS,  F(1), F(2), F(3), F(4), F(5), F(6), F(7), F(8), KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \
+  KC_TRNS,  KC_TRNS, KC_TRNS,  KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS),
+  #else
+  KC_TRNS,  KC_TRNS, KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS, KC_TRNS, KC_TRNS, \
+  KC_TRNS,  KC_TRNS, KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS, KC_TRNS, KC_TRNS, RESET, KC_TRNS, KC_TRNS, KC_TRNS, \
+  KC_TRNS,  KC_TRNS, KC_TRNS,  KC_TRNS, KC_TRNS,  KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \
+  KC_TRNS,  KC_TRNS, KC_TRNS,  KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,   KC_TRNS,  KC_TRNS, KC_UP, KC_TRNS, \
+  KC_TRNS,  KC_TRNS, KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \
+  KC_TRNS,  KC_TRNS, KC_TRNS,  KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS),
+  #endif
+};
+
+enum function_id {
+    SHIFT_ESC,
+    #ifdef RGBLIGHT_ENABLE
+    RGBLED_TOGGLE,
+    RGBLED_STEP_MODE,
+    RGBLED_INCREASE_HUE,
+    RGBLED_DECREASE_HUE,
+    RGBLED_INCREASE_SAT,
+    RGBLED_DECREASE_SAT,
+    RGBLED_INCREASE_VAL,
+    RGBLED_DECREASE_VAL
+    #endif
+};
+
+const uint16_t PROGMEM fn_actions[] = {
+  [0]  = ACTION_FUNCTION(SHIFT_ESC),
+  #ifdef RGBLIGHT_ENABLE
+  [1]  = ACTION_FUNCTION(RGBLED_TOGGLE),
+  [2]  = ACTION_FUNCTION(RGBLED_STEP_MODE),
+  [3]  = ACTION_FUNCTION(RGBLED_INCREASE_HUE),
+  [4]  = ACTION_FUNCTION(RGBLED_DECREASE_HUE),
+  [5]  = ACTION_FUNCTION(RGBLED_INCREASE_SAT),
+  [6]  = ACTION_FUNCTION(RGBLED_DECREASE_SAT),
+  [7]  = ACTION_FUNCTION(RGBLED_INCREASE_VAL),
+  [8]  = ACTION_FUNCTION(RGBLED_DECREASE_VAL),
+  #endif
+};
+
+void action_function(keyrecord_t *record, uint8_t id, uint8_t opt) {
+  static uint8_t shift_esc_shift_mask;
+  switch (id) {
+    case SHIFT_ESC:
+      shift_esc_shift_mask = get_mods()&MODS_CTRL_MASK;
+      if (record->event.pressed) {
+        if (shift_esc_shift_mask) {
+          add_key(KC_GRV);
+          send_keyboard_report();
+        } else {
+          add_key(KC_ESC);
+          send_keyboard_report();
+        }
+      } else {
+        if (shift_esc_shift_mask) {
+          del_key(KC_GRV);
+          send_keyboard_report();
+        } else {
+          del_key(KC_ESC);
+          send_keyboard_report();
+        }
+      }
+      break;
+    //led operations
+    #ifdef RGBLIGHT_ENABLE
+    case RGBLED_TOGGLE:
+      if (record->event.pressed) {
+        rgblight_toggle();
+      }
+      break;
+    case RGBLED_INCREASE_HUE:
+      if (record->event.pressed) {
+        rgblight_increase_hue();
+      }
+      break;
+    case RGBLED_DECREASE_HUE:
+      if (record->event.pressed) {
+        rgblight_decrease_hue();
+      }
+      break;
+    case RGBLED_INCREASE_SAT:
+      if (record->event.pressed) {
+        rgblight_increase_sat();
+      }
+      break;
+    case RGBLED_DECREASE_SAT:
+      if (record->event.pressed) {
+        rgblight_decrease_sat();
+      }
+      break;
+    case RGBLED_INCREASE_VAL:
+      if (record->event.pressed) {
+        rgblight_increase_val();
+      }
+      break;
+    case RGBLED_DECREASE_VAL:
+      if (record->event.pressed) {
+        rgblight_decrease_val();
+      }
+      break;
+    case RGBLED_STEP_MODE:
+      if (record->event.pressed) {
+        rgblight_step();
+      }
+      break;
+    #endif
+  }
+}
diff --git a/keyboard/phantom/led.c b/keyboard/phantom/led.c
new file mode 100644
index 0000000000..e45cc09648
--- /dev/null
+++ b/keyboard/phantom/led.c
@@ -0,0 +1,44 @@
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#include <avr/io.h>
+#include "stdint.h"
+#include "led.h"
+
+
+void led_init_ports() {
+    // * Set our LED pins as output
+    DDRB |= (1<<6);
+	DDRB |= (1<<7);
+}
+
+void led_set_kb(uint8_t usb_led) {
+    if (usb_led & (1<<USB_LED_CAPS_LOCK)) {
+        // Turn capslock on
+        PORTB |= (1<<6);
+    } else {
+        // Turn capslock off
+        PORTB &= ~(1<<6);
+    }
+	if (usb_led & (1<<USB_LED_SCROLL_LOCK)) {
+        // Turn scrolllock on
+        PORTB |= (1<<7);
+    } else {
+        // Turn scrolllock off
+        PORTB &= ~(1<<7);
+    }
+}
diff --git a/keyboard/phantom/phantom.c b/keyboard/phantom/phantom.c
new file mode 100644
index 0000000000..4328539d07
--- /dev/null
+++ b/keyboard/phantom/phantom.c
@@ -0,0 +1,28 @@
+#include "phantom.h"
+
+__attribute__ ((weak))
+void matrix_init_user(void) {
+	// leave these blank
+};
+
+__attribute__ ((weak))
+void matrix_scan_user(void) {
+	// leave these blank
+};
+
+void matrix_init_kb(void) {
+	// put your keyboard start-up code here
+	// runs once when the firmware starts up
+	if (matrix_init_user) {
+		(*matrix_init_user)();
+	}
+	led_init_ports();
+};
+
+void matrix_scan_kb(void) {
+	// put your looping keyboard code here
+	// runs every cycle (a lot)
+	if (matrix_scan_user) {
+		(*matrix_scan_user)();
+	}
+};
diff --git a/keyboard/phantom/phantom.h b/keyboard/phantom/phantom.h
new file mode 100644
index 0000000000..c1c7459ff4
--- /dev/null
+++ b/keyboard/phantom/phantom.h
@@ -0,0 +1,46 @@
+#ifndef PHANTOM_H
+#define PHANTOM_H
+
+#include "matrix.h"
+#include "keymap_common.h"
+#include <stddef.h>
+
+
+/* Phantom matrix layout
+   * ,-----------------------------------------------------------------------------.
+   * |00   |02| 03| 04| 05|  | 06| 07| 08| 09|   | 0a|0b |0c |0d |	|0e  |0f  |0g  |
+   * |-----------------------------------------------------------|	|--------------|
+   * | 01| 10| 11| 12| 13| 14| 15| 16| 17| 18| 19| 1a| 1b|  1d   |	|1e  |1f  |1g  |
+   * |-----------------------------------------------------------|	|--------------|
+   * |20   | 21| 22| 23| 24| 25| 26| 27| 28| 29| 2a| 2b| 2c|   2d|	| 2e | 2f | 2g |
+   * |-----------------------------------------------------------|	`--------------'
+   * |30     | 31| 32| 33| 34| 35| 36| 37| 38| 39| 3a| 3b| 3d    |
+   * |-----------------------------------------------------------|		 ,----.
+   * | 40     | 42| 43| 44| 45| 46| 47| 48| 49| 4a| 4b| 4d       |		 | 4f |
+   * |-----------------------------------------------------------|	 ,-------------.
+   * | 50 | 51 | 52 |      57               |5a  | 5b | 5c | 5d  |	 | 5e| 5f | 5g |
+   * `-----------------------------------------------------------'	 `-------------'
+ */
+// The first section contains all of the arguments
+// The second converts the arguments into a two-dimensional array
+#define KEYMAP( \
+	k00, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c, k0d, k0e, k0f, k0g, \
+	k01, k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, k1d, k1e, k1f, k1g, \
+	k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2c, k2d, k2e, k2f, k2g, \
+	k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, k3d, \
+	k40, k42, k43, k44, k45, k46, k47, k48, k49, k4a, k4b, k4d, k4f, \
+	k50, k51, k52, k57, k5a, k5b, k5c, k5d, k5e, k5f, k5g  \
+) \
+{ \
+		{k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c, k0d, k0e, k0f, k0g}, \
+		{k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, k1d, k1d, k1e, k1f, k1g}, \
+		{k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2c, k2d, k2e, k2f, k2g}, \
+		{k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, k3d, k3d, k3d, k3d, k3d}, \
+		{k40, k40, k42, k43, k44, k45, k46, k47, k48, k49, k4a, k4b, k4d, k4d, k4f, k4f, k4f},  \
+		{k50, k51, k52, k57, k57, k57, k57, k57, k57, k57, k5a, k5b, k5c, k5d, k5e, k5f, k5g} \
+}
+
+void matrix_init_user(void);
+void matrix_scan_user(void);
+
+#endif
diff --git a/keyboard/phantom/pinout.jpg b/keyboard/phantom/pinout.jpg
new file mode 100644
index 0000000000..30b0b8bf4b
Binary files /dev/null and b/keyboard/phantom/pinout.jpg differ
diff --git a/keyboard/phantom/pinout.txt b/keyboard/phantom/pinout.txt
new file mode 100644
index 0000000000..36f044d157
--- /dev/null
+++ b/keyboard/phantom/pinout.txt
@@ -0,0 +1 @@
+For WS2812B LED strip support, connect DIN from strip to PE2 on Teensy (see reference image pinout.jpg)
\ No newline at end of file