CLeaned out debug code
This commit is contained in:
jpetermans
parent
52f671c23e
commit
2c5b551970
3 changed files with 13 additions and 265 deletions
|
|
@ -29,26 +29,22 @@ void led_set(uint8_t usb_led) {
|
|||
msg_t msg;
|
||||
|
||||
if (usb_led & (1<<USB_LED_NUM_LOCK)) {
|
||||
// signal the LED control thread
|
||||
chSysUnconditionalLock();
|
||||
msg=(TOGGLE_NUM_LOCK << 8) | 1;
|
||||
chMBPostI(&led_mailbox, msg);
|
||||
chSysUnconditionalUnlock();
|
||||
} else {
|
||||
// signal the LED control thread
|
||||
chSysUnconditionalLock();
|
||||
msg=(TOGGLE_NUM_LOCK << 8) | 0;
|
||||
chMBPostI(&led_mailbox, msg);
|
||||
chSysUnconditionalUnlock();
|
||||
}
|
||||
if (usb_led & (1<<USB_LED_CAPS_LOCK)) {
|
||||
// signal the LED control thread
|
||||
chSysUnconditionalLock();
|
||||
msg=(TOGGLE_CAPS_LOCK << 8) | 1;
|
||||
chMBPostI(&led_mailbox, msg);
|
||||
chSysUnconditionalUnlock();
|
||||
} else {
|
||||
// signal the LED control thread
|
||||
chSysUnconditionalLock();
|
||||
msg=(TOGGLE_CAPS_LOCK << 8) | 0;
|
||||
chMBPostI(&led_mailbox, msg);
|
||||
|
|
|
|||
|
|
@ -17,7 +17,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|||
|
||||
/*
|
||||
* LED controller code
|
||||
* WF uses IS31FL3731C matrix LED driver from ISSI
|
||||
* IS31FL3731C matrix LED driver from ISSI
|
||||
* datasheet: http://www.issi.com/WW/pdf/31FL3731C.pdf
|
||||
*/
|
||||
|
||||
|
|
@ -56,9 +56,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|||
order same as above (CA 1st row (8bytes), CB 1st row (8bytes), ...)
|
||||
*/
|
||||
|
||||
/* Which LED should be used for CAPS LOCK indicator
|
||||
* The usual Caps Lock position is C4-6, so the address is
|
||||
* 0x24 + (4-1)*0x10 + (8-1) = 0x59 */
|
||||
// Which LED should be used for CAPS LOCK indicator
|
||||
#if !defined(CAPS_LOCK_LED_ADDRESS)
|
||||
#define CAPS_LOCK_LED_ADDRESS 46
|
||||
#endif
|
||||
|
|
@ -90,7 +88,6 @@ uint8_t rx[1] __attribute__((aligned(2)));
|
|||
uint8_t full_page[0xB4+1] = {0};
|
||||
|
||||
// LED mask (which LEDs are present, selected by bits)
|
||||
// See page comment above, control alternates CA matrix/CB matrix
|
||||
// IC60 pcb uses only CA matrix.
|
||||
// Each byte is a control pin for 8 leds ordered 8-1
|
||||
const uint8_t all_on_leds_mask[0x12] = {
|
||||
|
|
@ -182,11 +179,6 @@ static THD_FUNCTION(LEDthread, arg) {
|
|||
uint8_t temp, msg_type, msg_pin, msg_col, msg_led;
|
||||
msg_t msg;
|
||||
|
||||
/* //control register variables
|
||||
uint8_t page, save_page, save_breath1, save_breath2;
|
||||
msg_t msg, retval;
|
||||
*/
|
||||
|
||||
// initialize persistent variables
|
||||
pwm_step_status = 4; //full brightness
|
||||
page_status = 0; //start frame 0 (all off/on)
|
||||
|
|
@ -197,77 +189,51 @@ page_status = 0; //start frame 0 (all off/on)
|
|||
// be processed right away)
|
||||
chMBFetch(&led_mailbox, &msg, TIME_INFINITE);
|
||||
msg_col = (msg >> 24) & 0xFF;//if needed
|
||||
msg_pin = (msg >> 16) & 0XFF;//if needed (SET_FULL_ROW)
|
||||
msg_pin = (msg >> 16) & 0XFF;//if needed (e.g. SET_FULL_ROW)
|
||||
msg_type = (msg >> 8) & 0xFF; //second byte is msg type
|
||||
msg_led = (msg) & 0xFF; //first byte is action information
|
||||
|
||||
xprintf("--------------------\n");
|
||||
xprintf("mailbox fetch\nmsg: %X\n", msg);
|
||||
chThdSleepMilliseconds(20);
|
||||
xprintf("type: %X - pin: %X\n", msg_type, msg_pin);
|
||||
chThdSleepMilliseconds(20);
|
||||
xprintf("col: %X - led: %X\n", msg_col, msg_led);
|
||||
chThdSleepMilliseconds(10);
|
||||
|
||||
switch (msg_type){
|
||||
case KEY_LIGHT:
|
||||
//TODO: lighting key led on keypress
|
||||
break;
|
||||
|
||||
case SET_FULL_ROW:
|
||||
//write full byte to pin address, msg_pin = pin #, msg_led = byte to write
|
||||
//writes only to current page
|
||||
xprintf("SET_FULL_ROW\n");
|
||||
write_led_byte(page_status,msg_pin,msg_led);
|
||||
break;
|
||||
|
||||
case OFF_LED:
|
||||
//on/off/toggle single led, msg_led = row/col of led
|
||||
xprintf("OFF_LED: %d\n", msg_led);
|
||||
chThdSleepMilliseconds(10);
|
||||
set_led_bit(7, control_register_word, msg_led, 0);
|
||||
is31_write_data (7, control_register_word, 0x02);
|
||||
break;
|
||||
case ON_LED:
|
||||
xprintf("ON_LED: %d\n", msg_led);
|
||||
chThdSleepMilliseconds(10);
|
||||
set_led_bit(7, control_register_word, msg_led, 1);
|
||||
is31_write_data (7, control_register_word, 0x02);
|
||||
break;
|
||||
case TOGGLE_LED:
|
||||
xprintf("TOGGLE_LED: %d\n", msg_led);
|
||||
chThdSleepMilliseconds(10);
|
||||
set_led_bit(7, control_register_word, msg_led, 2);
|
||||
is31_write_data (7, control_register_word, 0x02);
|
||||
break;
|
||||
|
||||
case BLINK_OFF_LED:
|
||||
//on/off/toggle single led, msg_led = row/col of led
|
||||
xprintf("BLINK_ON: %d\n", msg_led);
|
||||
chThdSleepMilliseconds(10);
|
||||
set_led_bit(7, control_register_word, msg_led, 4);
|
||||
is31_write_data (7, control_register_word, 0x02);
|
||||
break;
|
||||
case BLINK_ON_LED:
|
||||
xprintf("BLINK_OFF: %d\n", msg_led);
|
||||
chThdSleepMilliseconds(10);
|
||||
set_led_bit(7, control_register_word, msg_led, 5);
|
||||
is31_write_data (7, control_register_word, 0x02);
|
||||
break;
|
||||
case BLINK_TOGGLE_LED:
|
||||
xprintf("BLINK_TOGGLE: %d\n", msg_led);
|
||||
chThdSleepMilliseconds(10);
|
||||
set_led_bit(7, control_register_word, msg_led, 6);
|
||||
is31_write_data (7, control_register_word, 0x02);
|
||||
break;
|
||||
|
||||
case TOGGLE_ALL:
|
||||
xprintf("TOGGLE_ALL: %d\n", msg_led);
|
||||
chThdSleepMilliseconds(10);
|
||||
//msg_led = unused
|
||||
is31_read_register(0, 0x00, &temp);//if first byte is on, then toggle frame 0 off
|
||||
is31_read_register(0, 0x00, &temp);
|
||||
led_control_reg[0] = 0;
|
||||
|
||||
//if first byte is on, then toggle frame 0 off
|
||||
if (temp==0 || page_status > 0) {
|
||||
__builtin_memcpy(led_control_reg+1, all_on_leds_mask, 0x12);
|
||||
} else {
|
||||
|
|
@ -287,8 +253,6 @@ page_status = 0; //start frame 0 (all off/on)
|
|||
|
||||
case TOGGLE_BACKLIGHT:
|
||||
//msg_led = on/off
|
||||
xprintf("TOGGLE_BACKLIGHT\n");
|
||||
chThdSleepMilliseconds(10);
|
||||
|
||||
//populate the 9 byte rows to be written to each pin, first byte is register (pin) address
|
||||
if (msg_led == 1) {
|
||||
|
|
@ -304,13 +268,9 @@ page_status = 0; //start frame 0 (all off/on)
|
|||
}
|
||||
break;
|
||||
|
||||
case DISPLAY_PAGE://show single layer indicator or full map of layer
|
||||
case DISPLAY_PAGE:
|
||||
//msg_led = page to toggle on
|
||||
xprintf("DISPLAY_PAGE\n");
|
||||
chThdSleepMilliseconds(10);
|
||||
if (page_status != msg_led) {
|
||||
xprintf(" - new page\n");
|
||||
chThdSleepMilliseconds(10);
|
||||
is31_write_register(IS31_FUNCTIONREG, IS31_REG_PICTDISP, msg_led);
|
||||
page_status = msg_led;
|
||||
|
||||
|
|
@ -321,8 +281,6 @@ page_status = 0; //start frame 0 (all off/on)
|
|||
|
||||
case RESET_PAGE:
|
||||
//led_msg = page to reset
|
||||
xprintf("RESET_PAGE\n");
|
||||
chThdSleepMilliseconds(10);
|
||||
led_control_reg[0] = 0;
|
||||
__builtin_memset(led_control_reg+1, 0, 0x12);
|
||||
is31_write_data(msg_led, led_control_reg, 0x13);
|
||||
|
|
@ -330,23 +288,14 @@ page_status = 0; //start frame 0 (all off/on)
|
|||
|
||||
case TOGGLE_NUM_LOCK:
|
||||
//msg_led = 0 or 1, off/on
|
||||
xprintf("NUMLOCK: %d\n", msg_led);
|
||||
chThdSleepMilliseconds(10);
|
||||
set_lock_leds(NUM_LOCK_LED_ADDRESS, msg_led, page_status);
|
||||
break;
|
||||
|
||||
case TOGGLE_CAPS_LOCK:
|
||||
xprintf("CAPSLOCK: %d\n", msg_led);
|
||||
chThdSleepMilliseconds(10);
|
||||
//msg_led = 0 or 1, off/on
|
||||
set_lock_leds(CAPS_LOCK_LED_ADDRESS, msg_led, page_status);
|
||||
break;
|
||||
|
||||
//TODO: MODE_BREATH
|
||||
|
||||
case STEP_BRIGHTNESS:
|
||||
xprintf("STEP_BACKLIGHT\n");
|
||||
chThdSleepMilliseconds(10);
|
||||
//led_msg = step pwm up or down
|
||||
switch (msg_led) {
|
||||
case 0:
|
||||
|
|
@ -375,137 +324,6 @@ page_status = 0; //start frame 0 (all off/on)
|
|||
is31_write_data(0,pwm_register_array,9);
|
||||
}
|
||||
break;
|
||||
|
||||
/* case LED_MSG_SLEEP_LED_ON:
|
||||
// save current settings
|
||||
is31_read_register(IS31_FUNCTIONREG, IS31_REG_PICTDISP, &save_page);
|
||||
is31_read_register(IS31_FUNCTIONREG, IS31_REG_BREATHCTRL1, &save_breath1);
|
||||
is31_read_register(IS31_FUNCTIONREG, IS31_REG_BREATHCTRL2, &save_breath2);
|
||||
// use pages 7 and 8 for (hardware) breathing (assuming they're empty)
|
||||
is31_write_register(6, BREATHE_LED_ADDRESS, 0xFF);
|
||||
is31_write_register(7, BREATHE_LED_ADDRESS, 0x00);
|
||||
is31_write_register(IS31_FUNCTIONREG, IS31_REG_BREATHCTRL1, (6<<4)|6);
|
||||
is31_write_register(IS31_FUNCTIONREG, IS31_REG_BREATHCTRL2, IS31_REG_BREATHCTRL2_ENABLE|3);
|
||||
retval = MSG_TIMEOUT;
|
||||
temp = 6;
|
||||
while(retval == MSG_TIMEOUT) {
|
||||
// switch to the other page
|
||||
is31_write_register(IS31_FUNCTIONREG, IS31_REG_PICTDISP, temp);
|
||||
temp = (temp == 6 ? 7 : 6);
|
||||
// the times should be sufficiently long for IS31 to finish switching pages
|
||||
retval = chMBFetch(&led_mailbox, &msg, MS2ST(temp == 6 ? 4000 : 6000));
|
||||
}
|
||||
// received a message (should be a wakeup), so restore previous state
|
||||
chThdSleepMilliseconds(3000); // need to wait until the page change finishes
|
||||
// note: any other messages are queued
|
||||
is31_write_register(IS31_FUNCTIONREG, IS31_REG_BREATHCTRL1, save_breath1);
|
||||
is31_write_register(IS31_FUNCTIONREG, IS31_REG_BREATHCTRL2, save_breath2);
|
||||
is31_write_register(IS31_FUNCTIONREG, IS31_REG_PICTDISP, save_page);
|
||||
break;
|
||||
case LED_MSG_SLEEP_LED_OFF:
|
||||
// should not get here; wakeup should be received in the branch above break;
|
||||
break;
|
||||
*/
|
||||
xprintf("--------------------\n");
|
||||
chThdSleepMilliseconds(10);
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
/* ==============================
|
||||
* debug function
|
||||
* ============================== */
|
||||
void print_debug(uint8_t page) {
|
||||
uint8_t j, debug_temp;
|
||||
//debugging code - print full led/blink/pwm registers on each frame
|
||||
xprintf("----layer state----: %X\n", layer_state);
|
||||
xprintf("page: %d\n", page);
|
||||
chThdSleepMilliseconds(10);
|
||||
for(j=0;j<0x24;j++){
|
||||
if(j > 0 && j % 9 == 0){
|
||||
xprintf("\n");
|
||||
}
|
||||
switch (j) {
|
||||
case 0:
|
||||
xprintf("\n--on-off--\n");
|
||||
chThdSleepMilliseconds(10);
|
||||
break;
|
||||
case 0x12:
|
||||
xprintf("\n--blink--\n");
|
||||
chThdSleepMilliseconds(10);
|
||||
break;
|
||||
}
|
||||
is31_read_register(page,j,&debug_temp);
|
||||
xprintf("%02X, ", debug_temp);
|
||||
chThdSleepMilliseconds(10);
|
||||
}
|
||||
|
||||
xprintf("\n--pwm--\n");
|
||||
chThdSleepMilliseconds(10);
|
||||
for(j=0x24;j<0xB4;j++) {
|
||||
is31_read_register(page,j,&debug_temp);
|
||||
xprintf("%02X, ", debug_temp);
|
||||
chThdSleepMilliseconds(10);
|
||||
if(j > 0x24 && (j-3) % 8 == 0){
|
||||
xprintf("\n");
|
||||
}
|
||||
}
|
||||
xprintf("\n");
|
||||
|
||||
//Function Register
|
||||
xprintf("\n--FUNCTION--\n");
|
||||
chThdSleepMilliseconds(10);
|
||||
for(j=0;j<0x0D;j++) {
|
||||
is31_read_register(0x0B,j,&debug_temp);
|
||||
switch(j) {
|
||||
case 0:
|
||||
xprintf("Config %02X", debug_temp);
|
||||
chThdSleepMilliseconds(2);
|
||||
break;
|
||||
case 1:
|
||||
xprintf(" - Pict %02X\n", debug_temp);
|
||||
chThdSleepMilliseconds(2);
|
||||
break;
|
||||
case 2:
|
||||
xprintf("Auto1 %02X", debug_temp);
|
||||
chThdSleepMilliseconds(2);
|
||||
break;
|
||||
case 3:
|
||||
xprintf(" - Auto2 %02X\n", debug_temp);
|
||||
chThdSleepMilliseconds(2);
|
||||
break;
|
||||
case 5:
|
||||
xprintf("Disp %02X", debug_temp);
|
||||
chThdSleepMilliseconds(2);
|
||||
break;
|
||||
case 6:
|
||||
xprintf(" - Audio %02X\n", debug_temp);
|
||||
chThdSleepMilliseconds(2);
|
||||
break;
|
||||
case 7:
|
||||
xprintf("Frame %02X", debug_temp);
|
||||
chThdSleepMilliseconds(2);
|
||||
break;
|
||||
case 8:
|
||||
xprintf(" - Breath1 %02X\n", debug_temp);
|
||||
chThdSleepMilliseconds(2);
|
||||
break;
|
||||
case 9:
|
||||
xprintf("Breath2 %02X - ", debug_temp);
|
||||
chThdSleepMilliseconds(2);
|
||||
break;
|
||||
case 10:
|
||||
xprintf(" - Shut %02X\n", debug_temp);
|
||||
chThdSleepMilliseconds(2);
|
||||
break;
|
||||
case 11:
|
||||
xprintf("AGC %02X", debug_temp);
|
||||
chThdSleepMilliseconds(2);
|
||||
break;
|
||||
case 12:
|
||||
xprintf(" - ADC %02X\n", debug_temp);
|
||||
chThdSleepMilliseconds(2);
|
||||
break;
|
||||
}
|
||||
}
|
||||
}
|
||||
|
|
@ -515,50 +333,29 @@ void print_debug(uint8_t page) {
|
|||
* ============================== */
|
||||
|
||||
void set_led_bit (uint8_t page, uint8_t *led_control_reg, uint8_t led_addr, uint8_t action) {
|
||||
//returns 2 bytes led control register address and byte to write
|
||||
//returns 2 bytes: led control register address and byte to write
|
||||
//0 - bit off, 1 - bit on, 2 - toggle bit
|
||||
|
||||
uint8_t control_reg_addr, column_bit, column_byte, bit_temp, blink_on;
|
||||
|
||||
//check for valid led address
|
||||
if (led_addr < 0 || led_addr > 87 || led_addr % 10 > 8) {
|
||||
xprintf("Invalid address: %d\n", led_addr);
|
||||
return;
|
||||
}
|
||||
|
||||
xprintf("set_led_bit: %d\n", led_addr);
|
||||
xprintf("action: %d\n", action);
|
||||
chThdSleepMilliseconds(10);
|
||||
//check blink bit
|
||||
//check for blink bit
|
||||
blink_on = action>>2;
|
||||
action &= ~(1<<2); //strip blink bit
|
||||
|
||||
//first byte is led control register address 0x00
|
||||
//msg_led tens column is pin#, ones column is bit position in 8-bit mask
|
||||
control_reg_addr = ((led_addr / 10) % 10 - 1 ) * 0x02;// A-register is every other byte
|
||||
xprintf("pre-reg_addr: %2X\n", control_reg_addr);
|
||||
chThdSleepMilliseconds(10);
|
||||
control_reg_addr += blink_on == 1 ? 0x12 : 0x00;//shift 12 bytes to blink register
|
||||
xprintf("blink-reg_addr: %2X\n", control_reg_addr);
|
||||
chThdSleepMilliseconds(10);
|
||||
xprintf("page: %2X\n", page);
|
||||
chThdSleepMilliseconds(10);
|
||||
|
||||
|
||||
is31_read_register(page, 0x06, &bit_temp);//maintain status of leds on this byte
|
||||
xprintf("reg 06: %2X\n", bit_temp);
|
||||
is31_read_register(page, 0x17, &bit_temp);//maintain status of leds on this byte
|
||||
xprintf("reg 17: %2X\n", bit_temp);
|
||||
is31_read_register(page, 0x18, &bit_temp);//maintain status of leds on this byte
|
||||
xprintf("reg 18: %2X\n", bit_temp);
|
||||
is31_read_register(page, 0x19, &bit_temp);//maintain status of leds on this byte
|
||||
xprintf("reg 19: %2X\n", bit_temp);
|
||||
is31_read_register(page, control_reg_addr, &bit_temp);//maintain status of leds on this byte
|
||||
column_bit = 1<<(led_addr % 10 - 1);
|
||||
column_byte = bit_temp;
|
||||
|
||||
xprintf("column_byte read: %2X\n", column_byte);
|
||||
chThdSleepMilliseconds(10);
|
||||
switch(action) {
|
||||
case 0:
|
||||
column_byte &= ~column_bit;
|
||||
|
|
@ -570,8 +367,6 @@ void set_led_bit (uint8_t page, uint8_t *led_control_reg, uint8_t led_addr, uint
|
|||
column_byte ^= column_bit;
|
||||
break;
|
||||
}
|
||||
xprintf("column_byte write: %2X\n", column_byte);
|
||||
chThdSleepMilliseconds(10);
|
||||
|
||||
//return word to be written in register
|
||||
led_control_reg[0] = control_reg_addr;
|
||||
|
|
@ -589,7 +384,7 @@ void write_led_byte (uint8_t page, uint8_t row, uint8_t led_byte) {
|
|||
void write_led_page (uint8_t page, uint8_t *user_led_array, uint8_t led_count) {
|
||||
uint8_t i;
|
||||
uint8_t pin, col;
|
||||
uint8_t led_control_register[0x13] = {0};//control register start address + 0x12 bytes
|
||||
uint8_t led_control_register[0x13] = {0};
|
||||
|
||||
__builtin_memset(led_control_register,0,13);
|
||||
|
||||
|
|
@ -607,30 +402,15 @@ void set_lock_leds(uint8_t led_addr, uint8_t led_action, uint8_t page) {
|
|||
uint8_t lock_temp;
|
||||
uint8_t led_control_word[2] = {0};
|
||||
|
||||
xprintf("---set lock---\n");
|
||||
chThdSleepMilliseconds(10);
|
||||
|
||||
//blink if all leds are on
|
||||
if (page == 0) {
|
||||
is31_read_register(0, 0x00, &lock_temp);
|
||||
xprintf("AllOnReg: %2X\n", lock_temp);
|
||||
chThdSleepMilliseconds(10);
|
||||
if (lock_temp == 0xFF) {
|
||||
xprintf("AllOntrue\n");
|
||||
chThdSleepMilliseconds(10);
|
||||
led_action |= (1<<2); //set blink bit
|
||||
} else {
|
||||
xprintf("AllOnfalse\n");
|
||||
chThdSleepMilliseconds(10);
|
||||
}
|
||||
}
|
||||
|
||||
set_led_bit(page,led_control_word,led_addr,led_action);
|
||||
|
||||
xprintf("led_word: %2X", led_control_word[0]);
|
||||
xprintf("%X\n", led_control_word[1]);
|
||||
chThdSleepMilliseconds(10);
|
||||
|
||||
is31_write_data(page, led_control_word, 0x02);
|
||||
}
|
||||
|
||||
|
|
@ -679,30 +459,3 @@ void led_controller_init(void) {
|
|||
chMBObjectInit(&led_mailbox, led_mailbox_queue, LED_MAILBOX_NUM_MSGS);
|
||||
chThdCreateStatic(waLEDthread, sizeof(waLEDthread), LOWPRIO, LEDthread, NULL);
|
||||
}
|
||||
|
||||
//TODO: Don't know equivalent QMK hooks for these
|
||||
//
|
||||
//void hook_usb_suspend_entry(void) {
|
||||
//#ifdef SLEEP_LED_ENABLE
|
||||
// chSysLockFromISR();
|
||||
// chMBPostI(&led_mailbox, LED_MSG_SLEEP_LED_ON);
|
||||
// chSysUnlockFromISR();
|
||||
//#endif /* SLEEP_LED_ENABLE */
|
||||
//}
|
||||
//
|
||||
//void hook_usb_suspend_loop(void) {
|
||||
// chThdSleepMilliseconds(100);
|
||||
// /* Remote wakeup */
|
||||
// if((USB_DRIVER.status & 2) && suspend_wakeup_condition()) {
|
||||
// send_remote_wakeup(&USB_DRIVER);
|
||||
// }
|
||||
//}
|
||||
//
|
||||
//void hook_usb_wakeup(void) {
|
||||
//#ifdef SLEEP_LED_ENABLE
|
||||
// chSysLockFromISR();
|
||||
// chMBPostI(&led_mailbox, LED_MSG_SLEEP_LED_OFF);
|
||||
// chSysUnlockFromISR();
|
||||
//#endif /* SLEEP_LED_ENABLE */
|
||||
//}
|
||||
//*/
|
||||
|
|
|
|||
|
|
@ -31,7 +31,6 @@ msg_t is31_read_register(uint8_t page, uint8_t reg, uint8_t *result);
|
|||
* ============================*/
|
||||
|
||||
void led_controller_init(void);
|
||||
void print_debug (uint8_t page);
|
||||
|
||||
#define CAPS_LOCK_LED_ADDRESS 46 //pin matrix location
|
||||
#define NUM_LOCK_LED_ADDRESS 85
|
||||
|
|
|
|||
Loading…
Reference in a new issue