1
0
Fork 0

Allow some usbconfig.h overrides at the keyboard level (#8647)

This commit is contained in:
Joel Challis 2020-04-29 00:17:54 +01:00 committed by GitHub
parent e02a3c559d
commit 374525c995
No known key found for this signature in database
GPG key ID: 4AEE18F83AFDEB23

View file

@ -24,15 +24,21 @@ section at the end of this file).
/* ---------------------------- Hardware Config ---------------------------- */ /* ---------------------------- Hardware Config ---------------------------- */
#ifndef USB_CFG_IOPORTNAME
#define USB_CFG_IOPORTNAME D #define USB_CFG_IOPORTNAME D
#endif
/* This is the port where the USB bus is connected. When you configure it to /* This is the port where the USB bus is connected. When you configure it to
* "B", the registers PORTB, PINB and DDRB will be used. * "B", the registers PORTB, PINB and DDRB will be used.
*/ */
#ifndef USB_CFG_DMINUS_BIT
#define USB_CFG_DMINUS_BIT 3 #define USB_CFG_DMINUS_BIT 3
#endif
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected. /* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
* This may be any bit in the port. * This may be any bit in the port.
*/ */
#ifndef USB_CFG_DPLUS_BIT
#define USB_CFG_DPLUS_BIT 2 #define USB_CFG_DPLUS_BIT 2
#endif
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected. /* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
* This may be any bit in the port. Please note that D+ must also be connected * This may be any bit in the port. Please note that D+ must also be connected
* to interrupt pin INT0! [You can also use other interrupts, see section * to interrupt pin INT0! [You can also use other interrupts, see section
@ -151,7 +157,9 @@ section at the end of this file).
/* This macro (if defined) is executed when a USB SET_ADDRESS request was /* This macro (if defined) is executed when a USB SET_ADDRESS request was
* received. * received.
*/ */
#ifndef USB_COUNT_SOF
#define USB_COUNT_SOF 1 #define USB_COUNT_SOF 1
#endif
/* define this macro to 1 if you need the global variable "usbSofCount" which /* define this macro to 1 if you need the global variable "usbSofCount" which
* counts SOF packets. This feature requires that the hardware interrupt is * counts SOF packets. This feature requires that the hardware interrupt is
* connected to D- instead of D+. * connected to D- instead of D+.
@ -321,10 +329,18 @@ section at the end of this file).
/* Set INT1 for D- falling edge to count SOF */ /* Set INT1 for D- falling edge to count SOF */
/* #define USB_INTR_CFG EICRA */ /* #define USB_INTR_CFG EICRA */
#ifndef USB_INTR_CFG_SET
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10)) #define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
#endif
/* #define USB_INTR_CFG_CLR 0 */ /* #define USB_INTR_CFG_CLR 0 */
/* #define USB_INTR_ENABLE EIMSK */ /* #define USB_INTR_ENABLE EIMSK */
#ifndef USB_INTR_ENABLE_BIT
#define USB_INTR_ENABLE_BIT INT1 #define USB_INTR_ENABLE_BIT INT1
#endif
/* #define USB_INTR_PENDING EIFR */ /* #define USB_INTR_PENDING EIFR */
#ifndef USB_INTR_PENDING_BIT
#define USB_INTR_PENDING_BIT INTF1 #define USB_INTR_PENDING_BIT INTF1
#endif
#ifndef USB_INTR_VECTOR
#define USB_INTR_VECTOR INT1_vect #define USB_INTR_VECTOR INT1_vect
#endif