1
0
Fork 0

Cleanup rules.mk for 32U4 keyboards, N-Q (#7147)

This commit is contained in:
fauxpark 2019-10-26 12:32:18 +11:00 committed by Drashna Jaelre
parent 006ec86786
commit 5d34e70cf7
60 changed files with 300 additions and 1480 deletions

View file

@ -1 +1 @@
MOUSEKEY_ENABLE = yes # Mouse keys(+4700) MOUSEKEY_ENABLE = yes

View file

@ -11,9 +11,6 @@ MCU = atmega32u4
# ATmega328P USBasp # ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Build Options # Build Options
# change to "no" to disable the options, or define them in the Makefile in # change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically # the appropriate keymap folder that will get included automatically

View file

@ -1,80 +0,0 @@
# MCU name
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
# atmega32a bootloadHID
BOOTLOADER = atmel-dfu
# Build Options
# change yes to no to disable
#
BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = yes # Console for debug(+400)
COMMAND_ENABLE = yes # Commands for debug and configuration
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
NKRO_ENABLE = no # USB Nkey Rollover
BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default
MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config)
UNICODE_ENABLE = no # Unicode
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE = no # Audio output on port C6
FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches
HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400)
#UNICODEMAP_ENABLE = yes # for emoji user
#RGBLIGHT_ENABLE = yes # uncomment if you want addressable led strips

View file

@ -1,80 +0,0 @@
# MCU name
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
# atmega32a bootloadHID
BOOTLOADER = atmel-dfu
# Build Options
# change yes to no to disable
#
BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = yes # Console for debug(+400)
COMMAND_ENABLE = yes # Commands for debug and configuration
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
NKRO_ENABLE = no # USB Nkey Rollover
BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default
MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config)
UNICODE_ENABLE = no # Unicode
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE = no # Audio output on port C6
FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches
HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400)
#UNICODEMAP_ENABLE = yes # for emoji user
#RGBLIGHT_ENABLE = yes # uncomment if you want addressable led strips

View file

@ -0,0 +1,35 @@
# MCU name
MCU = atmega32u4
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
# ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu
# Build Options
# change yes to no to disable
#
BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = yes # Console for debug(+400)
COMMAND_ENABLE = yes # Commands for debug and configuration
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
NKRO_ENABLE = no # USB Nkey Rollover
BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default
MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config)
UNICODE_ENABLE = no # Unicode
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE = no # Audio output on port C6
FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches
HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400)
#UNICODEMAP_ENABLE = yes # for emoji user
#RGBLIGHT_ENABLE = yes # uncomment if you want addressable led strips

View file

@ -1,14 +1,17 @@
SRC = matrix.c mcp23017.c # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency
F_CPU = 8000000 F_CPU = 8000000
ARCH = AVR8 # Bootloader selection
F_USB = $(F_CPU) # Teensy halfkay
# Pro Micro caterina
# Interrupt driven control endpoint task(+60) # Atmel DFU atmel-dfu
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
# ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
@ -30,4 +33,6 @@ FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches
HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400)
CUSTOM_MATRIX = yes CUSTOM_MATRIX = yes
DEBUG_ENABLE = yes DEBUG_ENABLE = yes
BLUETOOTH = AdafruitBLE BLUETOOTH = AdafruitBLE
SRC += matrix.c mcp23017.c

View file

@ -1,48 +1,14 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
BOOTLOADER = caterina BOOTLOADER = caterina
# Build Options # Build Options

View file

@ -1,27 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #

View file

@ -1,12 +1,14 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Boot Section Size in *bytes* # Bootloader selection
# Teensy halfKay 512 # Teensy halfkay
# Teensy++ halfKay 1024 # Pro Micro caterina
# Atmel DFU loader 4096 # Atmel DFU atmel-dfu
# LUFA bootloader 4096 # LUFA DFU lufa-dfu
# USBaspLoader 2048 # QMK DFU qmk-dfu
# ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# Build Options # Build Options

View file

@ -1,63 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #

View file

@ -1,63 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #

View file

@ -7,7 +7,8 @@ MCU = atmega32u4
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# Build Options # Build Options
@ -32,4 +33,4 @@ FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches
HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400)
EXTRAFLAGS += -flto EXTRAFLAGS += -flto
LAYOUTS = 60_ansi 60_iso 60_hhkb 60_tsangan_hhkb LAYOUTS = 60_ansi 60_iso 60_hhkb 60_tsangan_hhkb

View file

@ -1,45 +1,15 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to BOOTLOADER = atmel-dfu
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# comment out to disable the options. # comment out to disable the options.
@ -53,4 +23,4 @@ SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality
AUDIO_ENABLE ?= no AUDIO_ENABLE ?= no
RGBLIGHT_ENABLE ?= no RGBLIGHT_ENABLE ?= no

View file

@ -1,53 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #
@ -69,4 +32,4 @@ AUDIO_ENABLE = no # Audio output on port C6
FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches
HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400)
LAYOUTS = 65_ansi_blocker LAYOUTS = 65_ansi_blocker

View file

@ -1,63 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #

View file

@ -1,63 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #

View file

@ -1,51 +1,15 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to BOOTLOADER = atmel-dfu
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# comment out to disable the options. # comment out to disable the options.

View file

@ -1,63 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# comment out to disable the options. # comment out to disable the options.
# #
@ -70,4 +23,4 @@ SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
AUDIO_ENABLE = no AUDIO_ENABLE = no
RGBLIGHT_ENABLE = no RGBLIGHT_ENABLE = no

View file

@ -1,52 +1,15 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Bootloader selection
# Processor frequency. # Teensy halfkay
# This will define a symbol, F_CPU, in all source code files equal to the # Pro Micro caterina
# processor frequency in Hz. You can then use this symbol in your source code to # Atmel DFU atmel-dfu
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # LUFA DFU lufa-dfu
# automatically to create a 32-bit value in your source code. # QMK DFU qmk-dfu
# # ATmega32A bootloadHID
# This will be an integer division of F_USB below, as it is sourced by # ATmega328P USBasp
# F_USB after it has run through any CPU prescalers. Note that this value BOOTLOADER = atmel-dfu
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
# LUFA specific
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
AUDIO_ENABLE = no # Audio output on port C6 AUDIO_ENABLE = no # Audio output on port C6

View file

@ -1,2 +1,11 @@
BACKLIGHT_ENABLE = no # Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
# ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
BACKLIGHT_ENABLE = no

View file

@ -1,2 +1,11 @@
BACKLIGHT_ENABLE = no # Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
# ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
BACKLIGHT_ENABLE = no

View file

@ -1,2 +1,11 @@
BACKLIGHT_ENABLE = no # Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
# ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = halfkay BOOTLOADER = halfkay
BACKLIGHT_ENABLE = no

View file

@ -1,46 +1,6 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Bootloader
# This definition is optional, and if your keyboard supports multiple bootloaders of
# different sizes, comment this out, and the correct address will be loaded
# automatically (+60). See bootloader.mk for all options.
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Build Options # Build Options
# change to "no" to disable the options, or define them in the Makefile in # change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically # the appropriate keymap folder that will get included automatically

View file

@ -1,63 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #

View file

@ -1,63 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #

View file

@ -1,45 +1,14 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
OPT_DEFS += -DBOOTLOADER_SIZE=4096
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# Build Options # Build Options
@ -59,4 +28,4 @@ RGBLIGHT_ENABLE ?= yes
#PS2_USE_USART ?= yes #PS2_USE_USART ?= yes
#PS2_USE_INT ?= yes #PS2_USE_INT ?= yes
LAYOUTS = 60_ansi LAYOUTS = 60_ansi

View file

@ -1,16 +1,22 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Processor frequency
F_CPU = 8000000 F_CPU = 8000000
# Bootloader # Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
# ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
# Build Options # Build Options
# comment out to disable the options. # comment out to disable the options.
# #
BLUETOOTH = AdafruitBLE BLUETOOTH = AdafruitBLE
BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = no # Mouse keys(+4700) MOUSEKEY_ENABLE = no # Mouse keys(+4700)

View file

@ -1,8 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Bootloader # Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
# ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
# Build Options # Build Options
# comment out to disable the options. # comment out to disable the options.
# #

View file

@ -1,63 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #

View file

@ -1,9 +1,5 @@
# MCU name
MCU = atmega32u4 MCU = atmega32u4
F_CPU = 16000000
ARCH = AVR8
F_USB = $(F_CPU)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
@ -11,7 +7,8 @@ OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# Build Options # Build Options
@ -36,4 +33,4 @@ FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches
HD44780_ENABLE = no # Enable support for HD44780 based LCDs HD44780_ENABLE = no # Enable support for HD44780 based LCDs
EXTRAFLAGS += -flto EXTRAFLAGS += -flto
LAYOUTS = numpad_5x4 LAYOUTS = numpad_5x4

View file

@ -1,34 +1 @@
# Copyright 2013 Jun Wako <wakojun@gmail.com> CONSOLE_ENABLE = yes
#
# This program is free software: you can redistribute it and/or modify
# it under the terms of the GNU General Public License as published by
# the Free Software Foundation, either version 2 of the License, or
# (at your option) any later version.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program. If not, see <http://www.gnu.org/licenses/>.
# QMK Build Options
# change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically
#
BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = yes # Console for debug(+400)
COMMAND_ENABLE = yes # Commands for debug and configuration
NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality
MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config)
AUDIO_ENABLE = no # Audio output on port C6
UNICODE_ENABLE = no # Unicode
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time.
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend

View file

@ -1,51 +1,15 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to BOOTLOADER = halfkay
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable

View file

@ -1,18 +0,0 @@
# Build Options
# change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically
#
BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = no # Mouse keys(+4700)
EXTRAKEY_ENABLE = no # Audio control and System control(+450)
CONSOLE_ENABLE = no # Console for debug(+400)
COMMAND_ENABLE = no # Commands for debug and configuration
NKRO_ENABLE = no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality
MIDI_ENABLE = no # MIDI controls
AUDIO_ENABLE = no # Audio output on port C6
UNICODE_ENABLE = no # Unicode
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight.
SWAP_HANDS_ENABLE = no # Enable one-hand typing

View file

@ -1 +0,0 @@
# empty

View file

@ -1,18 +0,0 @@
# Build Options
# change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically
#
BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = no # Mouse keys(+4700)
EXTRAKEY_ENABLE = no # Audio control and System control(+450)
CONSOLE_ENABLE = no # Console for debug(+400)
COMMAND_ENABLE = no # Commands for debug and configuration
NKRO_ENABLE = no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality
MIDI_ENABLE = no # MIDI controls
AUDIO_ENABLE = no # Audio output on port C6
UNICODE_ENABLE = no # Unicode
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight.
SWAP_HANDS_ENABLE = no # Enable one-hand typing

View file

@ -1 +0,0 @@
# empty

View file

@ -1,63 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #

View file

@ -1,9 +1,6 @@
# Cortex version # Cortex version
MCU = STM32F303 MCU = STM32F303
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Build Options # Build Options
# change to "no" to disable the options, or define them in the Makefile in # change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically # the appropriate keymap folder that will get included automatically

View file

@ -1,8 +1,15 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Interrupt driven control endpoint task(+60) # Bootloader selection
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT # Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
# ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu
# Build Options # Build Options
# change to "no" to disable the options, or define them in the Makefile in # change to "no" to disable the options, or define them in the Makefile in

View file

@ -1,8 +1,15 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Interrupt driven control endpoint task(+60) # Bootloader selection
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT # Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
# ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu
# Build Options # Build Options
# change to "no" to disable the options, or define them in the Makefile in # change to "no" to disable the options, or define them in the Makefile in

View file

@ -1,15 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Bootloader # Bootloader selection
# This definition is optional, and if your keyboard supports multiple bootloaders of # Teensy halfkay
# different sizes, comment this out, and the correct address will be loaded # Pro Micro caterina
# automatically (+60). See bootloader.mk for all options. # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
# ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Build Options # Build Options
# change to "no" to disable the options, or define them in the Makefile in # change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically # the appropriate keymap folder that will get included automatically

View file

@ -1,15 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Bootloader # Bootloader selection
# This definition is optional, and if your keyboard supports multiple bootloaders of # Teensy halfkay
# different sizes, comment this out, and the correct address will be loaded # Pro Micro caterina
# automatically (+60). See bootloader.mk for all options. # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
# ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Build Options # Build Options
# change to "no" to disable the options, or define them in the Makefile in # change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically # the appropriate keymap folder that will get included automatically

View file

@ -1,15 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Bootloader # Bootloader selection
# This definition is optional, and if your keyboard supports multiple bootloaders of # Teensy halfkay
# different sizes, comment this out, and the correct address will be loaded # Pro Micro caterina
# automatically (+60). See bootloader.mk for all options. # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
# ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = qmk-dfu BOOTLOADER = qmk-dfu
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Build Options # Build Options
# change to "no" to disable the options, or define them in the Makefile in # change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically # the appropriate keymap folder that will get included automatically

View file

@ -4,9 +4,6 @@ LAYOUTS += ortho_4x12
# Cortex version # Cortex version
MCU = STM32F303 MCU = STM32F303
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Build Options # Build Options
# change to "no" to disable the options, or define them in the Makefile in # change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically # the appropriate keymap folder that will get included automatically

View file

@ -1,6 +1,14 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
# ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# Build Options # Build Options

View file

@ -1,45 +1,15 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to BOOTLOADER = atmel-dfu
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
BOOTLOADER=amtel-dfu
# Build Options # Build Options
# comment out to disable the options. # comment out to disable the options.

View file

@ -1,47 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Bootloader
# This definition is optional, and if your keyboard supports multiple bootloaders of
# different sizes, comment this out, and the correct address will be loaded
# automatically (+60). See bootloader.mk for all options.
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Build Options # Build Options
# change to "no" to disable the options, or define them in the Makefile in # change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically # the appropriate keymap folder that will get included automatically

View file

@ -1,47 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Bootloader
# This definition is optional, and if your keyboard supports multiple bootloaders of
# different sizes, comment this out, and the correct address will be loaded
# automatically (+60). See bootloader.mk for all options.
BOOTLOADER = qmk-dfu BOOTLOADER = qmk-dfu
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Build Options # Build Options
# change to "no" to disable the options, or define them in the Makefile in # change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically # the appropriate keymap folder that will get included automatically

View file

@ -1,63 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #
@ -77,4 +30,4 @@ UNICODE_ENABLE = no # Unicode
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE = no # Audio output on port C6 AUDIO_ENABLE = no # Audio output on port C6
FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches
HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400)

View file

@ -1,63 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #

View file

@ -1,45 +1,15 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to BOOTLOADER = atmel-dfu
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# comment out to disable the options. # comment out to disable the options.
@ -53,4 +23,4 @@ SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality
AUDIO_ENABLE ?= no AUDIO_ENABLE ?= no
RGBLIGHT_ENABLE ?= no RGBLIGHT_ENABLE ?= no

View file

@ -1,50 +1,14 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
BOOTLOADER = halfkay BOOTLOADER = halfkay
# Build Options # Build Options

View file

@ -1,63 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #

View file

@ -1,47 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Bootloader
# This definition is optional, and if your keyboard supports multiple bootloaders of
# different sizes, comment this out, and the correct address will be loaded
# automatically (+60). See bootloader.mk for all options.
BOOTLOADER = caterina BOOTLOADER = caterina
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Build Options # Build Options
# change to "no" to disable the options, or define them in the Makefile in # change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically # the appropriate keymap folder that will get included automatically