diff --git a/m0110.c b/m0110.c index 522c3ec0dc..a669c85a48 100644 --- a/m0110.c +++ b/m0110.c @@ -1,5 +1,5 @@ /* -Copyright 2011 Jun WAKO +Copyright 2011,2012 Jun WAKO This software is licensed with a Modified BSD License. All of this is supposed to be Free Software, Open Source, DFSG-free, @@ -34,6 +34,7 @@ CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. */ +/* M0110A Support was contributed by skagon@github */ #include #include @@ -43,6 +44,9 @@ POSSIBILITY OF SUCH DAMAGE. #include "debug.h" +static inline uint8_t raw2scan(uint8_t raw); +static inline uint8_t inquiry(void); +static inline uint8_t instant(void); static inline void clock_lo(void); static inline void clock_hi(void); static inline bool clock_in(void); @@ -57,130 +61,6 @@ static inline void idle(void); static inline void request(void); -/* -Primitive M0110 Library for AVR -============================== - - -Signaling ---------- -CLOCK is always from KEYBOARD. DATA are sent with MSB first. - -1) IDLE: both lines are high. - CLOCK ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ - DATA ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ - -2) KEYBOARD->HOST: HOST reads bit on rising edge. - CLOCK ~~~~~~~~~~~~|__|~~~|__|~~~|__|~~~|__|~~~|__|~~~|__|~~~|__|~~~|__|~~~~~~~~~~~ - DATA ~~~~~~~~~~~~X777777X666666X555555X444444X333333X222222X111111X000000X~~~~~~~ - <--> 160us(clock low) - <---> 180us(clock high) - -3) HOST->KEYBOARD: HOST asserts bit on falling edge. - CLOCK ~~~~~~~~~~~~|__|~~~|__|~~~|__|~~~|__|~~~|__|~~~|__|~~~|__|~~~|__|~~~~~~~~~~~ - DATA ~~~~~~|_____X777777X666666X555555X444444X333333X222222X111111X000000X~~~~~~~ - <----> 840us(request to send by host) <---> 80us(hold DATA) - <--> 180us(clock low) - <---> 220us(clock high) - - -Protocol --------- -COMMAND: - Inquiry 0x10 get key event - Instant 0x12 get key event - Model 0x14 get model number(M0110 responds with 0x09) - bit 7 1 if another device connected(used when keypad exists?) - bit4-6 next device model number - bit1-3 keyboard model number - bit 0 always 1 - Test 0x16 test(ACK:0x7D/NAK:0x77) - -KEY EVENT: - bit 7 key state(0:press 1:release) - bit 6-1 scan code(see below) - bit 0 always 1 - To get scan code use this: ((bits&(1<<7)) | ((bits&0x7F))>>1). - - Note: On the M0110A, the numpad keys and the arrow keys are preceded by 0x79. - Moreover, the numpad keys =, /, * and + are preceded by shift-down 0x71 on press and shift-up 0xF1 on release. - So, the data transferred by nupmad 5 is "79 2F" whereas for numpad + it's "71 79 0D". - -SCAN CODE: - m0111_recv_key() function returns follwing scan codes instead of raw key events. - Scan codes are 1 byte long and bit7 is set when key is released. - - M0110 - ,---------------------------------------------------------. - | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backs| - |---------------------------------------------------------| - |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| \| - |---------------------------------------------------------| - |CapsLo| A| S| D| F| G| H| J| K| L| ;| '|Return| - |---------------------------------------------------------| - |Shift | Z| X| C| V| B| N| M| ,| ,| /| | - `---------------------------------------------------------' - |Opt|Mac | Space |Enter|Opt| - `------------------------------------------------' - ,---------------------------------------------------------. - | 32| 12| 13| 14| 15| 17| 16| 1A| 1C| 19| 1D| 1B| 18| 33| - |---------------------------------------------------------| - | 30| 0C| 0D| 0E| 0F| 10| 11| 20| 22| 1F| 23| 21| 1E| 2A| - |---------------------------------------------------------| - | 39| 00| 01| 02| 03| 05| 04| 26| 28| 25| 29| 27| 24| - |---------------------------------------------------------| - | 38| 06| 07| 08| 09| 0B| 2D| 2E| 2B| 2F| 2C| 38| - `---------------------------------------------------------' - | 3A| 37| 31 | 34| 3A| - `------------------------------------------------' - - M0110A - ,---------------------------------------------------------. ,---------------. - | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Bcksp| |Clr| =| /| *| - |---------------------------------------------------------| |---------------| - |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| | | 7| 8| 9| -| - |-----------------------------------------------------' | |---------------| - |CapsLo| A| S| D| F| G| H| J| K| L| ;| '|Return| | 4| 5| 6| +| - |---------------------------------------------------------| |---------------| - |Shift | Z| X| C| V| B| N| M| ,| ,| /|Shft|Up | | 1| 2| 3| | - |---------------------------------------------------------' |-----------|Ent| - |Optio|Mac | Space | \|Lft|Rgt|Dn | | 0| .| | - `---------------------------------------------------------' `---------------' - ,---------------------------------------------------------. ,---------------. - | 32| 12| 13| 14| 15| 17| 16| 1A| 1C| 19| 1D| 1B| 18| 33| | 47| 68| 6D| 62| - |---------------------------------------------------------| |---------------| - | 30| 0C| 0D| 0E| 0F| 10| 11| 20| 22| 1F| 23| 21| 1E| | | 59| 5B| 5C| 4E| - |-----------------------------------------------------' | |---------------| - | 39| 00| 01| 02| 03| 05| 04| 26| 28| 25| 29| 27| 24| | 56| 57| 58| 66| - |---------------------------------------------------------| |---------------| - | 38| 06| 07| 08| 09| 0B| 2D| 2E| 2B| 2F| 2C| 38| 4D| | 53| 54| 55| | - |---------------------------------------------------------' |-----------| 4C| - | 3A| 37| 31 | 2A| 46| 42| 48| | 52| 41| | - `---------------------------------------------------------' `---------------' - - -References ----------- -Technical Info for 128K/512K and Plus - ftp://ftp.apple.asimov.net/pub/apple_II/documentation/macintosh/Mac%20Hardware%20Info%20-%20Mac%20128K.pdf - ftp://ftp.apple.asimov.net/pub/apple_II/documentation/macintosh/Mac%20Hardware%20Info%20-%20Mac%20Plus.pdf -Protocol: - Page 20 of Tech Info for 128K/512K - http://www.mac.linux-m68k.org/devel/plushw.php -Connector: - Page 20 of Tech Info for 128K/512K - http://www.kbdbabel.org/conn/kbd_connector_macplus.png -Signaling: - http://www.kbdbabel.org/signaling/kbd_signaling_mac.png - http://typematic.blog.shinobi.jp/Entry/14/ -Scan Codes: - Page 22 of Tech Info for 128K/512K - Page 07 of Tech Info for Plus - http://m0115.web.fc2.com/m0110.jpg - http://m0115.web.fc2.com/m0110a.jpg -*/ - - #define WAIT_US(stat, us, err) do { \ if (!wait_##stat(us)) { \ m0110_error = err; \ @@ -202,6 +82,9 @@ Scan Codes: } \ } while (0) +#define KEY(raw) ((raw) & 0x7f) +#define IS_BREAK(raw) (((raw) & 0x80) == 0x80) + uint8_t m0110_error = 0; @@ -212,10 +95,6 @@ void m0110_init(void) idle(); _delay_ms(1000); - // Model Number - // M0110 : 0x09 00001001 : model number 4 (100) - // M0110A: 0x0B 00001011 : model number 5 (101) - // M0110 & M0120: ??? m0110_send(M0110_MODEL); data = m0110_recv(); print("m0110_init model: "); phex(data); print("\n"); @@ -273,18 +152,180 @@ ERROR: return 0xFF; } +/* +Handling for exceptional case of key combinations for M0110A + +Shift and Calc/Arrow key could be operated simultaneously: + + Case Shift Arrow Events Interpret + ------------------------------------------------------------------- + 1 Down Down 71, 79, DD Calc(d)*a *b + 2 Down Up 71, 79, UU Arrow&Calc(u)*a + 3 Up Down F1, 79, DD Shift(u) *c + 4 Up Up F1, 79, UU Shift(u) and Arrow&Calc(u)*a + + Case Shift Calc Events Interpret + ------------------------------------------------------------------- + 5(1) Down Down 71, 71, 79, DD Shift(d) and Cacl(d) + 6(2) Down Up F1, 71, 79, UU Shift(u) and Arrow&Calc(u)*a + 7(1) Up Down F1, 71, 79, DD Shift(u) and Calc(d) + 8(4) Up Up F1, F1, 79, UU Shift(ux2) and Arrow&Calc(u)*a + +During Calc key is hold: + Case Shift Arrow Events Interpret + ------------------------------------------------------------------- + A(3) ---- Down F1, 79, DD Shift(u) *c + B ---- Up 79, UU Arrow&Calc(u)*a + C Down ---- F1, 71 Shift(u) and Shift(d) + D Up ---- F1 Shift(u) + E Hold Down 79, DD Normal + F Hold Up 79, UU Arrow&Calc(u)*a + G(1) Down Down F1, 71, 79, DD Shift(u)*b and Calc(d)*a + H(2) Down Up F1, 71, 79, UU Shift(u) and Arrow&Calc(u)*a + I(3) Up Down F1, F1, 79, DD Shift(ux2) *c + J(4) Up Up F1, 79, UU Shift(u) and Arrow&Calc(u)*a + + Case Shift Calc Events Interpret + ------------------------------------------------------------------- + K(1) ---- Down 71, 79, DD Calc(d)*a + L(4) ---- Up F1, 79, UU Shift(u) and Arrow&Calc(u)*a + M(1) Hold Down 71, 79, DD Calc(d)*a + N Hold Up 79, UU Arrow&Calc(u)*a + + Where DD/UU indicates part of Keypad Down/Up event. + *a: Impossible to distinguish btween Arrow and Calc event. + *b: Shift(d) event is ignored. + *c: Arrow/Calc(d) event is ignored. +*/ uint8_t m0110_recv_key(void) { - uint8_t key; - m0110_send(M0110_INQUIRY); - key = m0110_recv(); - if (key == 0xFF || key == M0110_NULL) - return M0110_NULL; - else - return M0110_RAW2SCAN(key); + static uint8_t keybuf = 0x00; + static uint8_t keybuf2 = 0x00; + static uint8_t rawbuf = 0x00; + uint8_t raw, raw2, raw3; + + if (keybuf) { + raw = keybuf; + keybuf = 0x00; + return raw; + } + if (keybuf2) { + raw = keybuf2; + keybuf2 = 0x00; + return raw; + } + + if (rawbuf) { + raw = rawbuf; + rawbuf = 0x00; + } else { + raw = instant(); // Use INSTANT for better response. Should be INQUIRY ? + } + switch (KEY(raw)) { + case M0110_KEYPAD: + raw2 = instant(); + switch (KEY(raw2)) { + case M0110_ARROW_UP: + case M0110_ARROW_DOWN: + case M0110_ARROW_LEFT: + case M0110_ARROW_RIGHT: + if (IS_BREAK(raw2)) { + // Case B,F,N: + keybuf = (raw2scan(raw2) | M0110_CALC_OFFSET); // Calc(u) + return (raw2scan(raw2) | M0110_KEYPAD_OFFSET); // Arrow(u) + } + break; + } + // Keypad or Arrow + return (raw2scan(raw2) | M0110_KEYPAD_OFFSET); + break; + case M0110_SHIFT: + raw2 = instant(); + switch (KEY(raw2)) { + case M0110_SHIFT: + // Case: 5-8,C,G,H + rawbuf = raw2; + return raw2scan(raw); // Shift(d/u) + break; + case M0110_KEYPAD: + // Shift + Arrow, Calc, or etc. + raw3 = instant(); + switch (KEY(raw3)) { + case M0110_ARROW_UP: + case M0110_ARROW_DOWN: + case M0110_ARROW_LEFT: + case M0110_ARROW_RIGHT: + if (IS_BREAK(raw)) { + if (IS_BREAK(raw3)) { + // Case 4: + print("(4)\n"); + keybuf2 = raw2scan(raw); // Shift(u) + keybuf = (raw2scan(raw3) | M0110_CALC_OFFSET); // Calc(u) + return (raw2scan(raw3) | M0110_KEYPAD_OFFSET); // Arrow(u) + } else { + // Case 3: + print("(3)\n"); + return (raw2scan(raw)); // Shift(u) + } + } else { + if (IS_BREAK(raw3)) { + // Case 2: + print("(2)\n"); + keybuf = (raw2scan(raw3) | M0110_CALC_OFFSET); // Calc(u) + return (raw2scan(raw3) | M0110_KEYPAD_OFFSET); // Arrow(u) + } else { + // Case 1: + print("(1)\n"); + return (raw2scan(raw3) | M0110_CALC_OFFSET); // Calc(d) + } + } + break; + default: + // Shift + Keypad + keybuf = (raw2scan(raw3) | M0110_KEYPAD_OFFSET); + return raw2scan(raw); // Shift(d/u) + break; + } + break; + default: + // Shift + Normal keys + keybuf = raw2scan(raw2); + return raw2scan(raw); // Shift(d/u) + break; + } + break; + default: + // Normal keys + return raw2scan(raw); + break; + } } +static inline uint8_t raw2scan(uint8_t raw) { + return (raw == M0110_NULL) ? M0110_NULL : ( + (raw == M0110_ERROR) ? M0110_ERROR : ( + ((raw&0x80) | ((raw&0x7F)>>1)) + ) + ); +} + +static inline uint8_t inquiry(void) +{ + m0110_send(M0110_INQUIRY); + return m0110_recv(); +} + +static inline uint8_t instant(void) +{ + m0110_send(M0110_INSTANT); + uint8_t data = m0110_recv(); + if (data != M0110_NULL) { + phex(data); print(" "); + } + return data; +} + static inline void clock_lo() { M0110_CLOCK_PORT &= ~(1<HOST: HOST reads bit on rising edge. + CLOCK ~~~~~~~~~~~~|__|~~~|__|~~~|__|~~~|__|~~~|__|~~~|__|~~~|__|~~~|__|~~~~~~~~~~~ + DATA ~~~~~~~~~~~~X777777X666666X555555X444444X333333X222222X111111X000000X~~~~~~~ + <--> 160us(clock low) + <---> 180us(clock high) + +3) HOST->KEYBOARD: HOST asserts bit on falling edge. + CLOCK ~~~~~~~~~~~~|__|~~~|__|~~~|__|~~~|__|~~~|__|~~~|__|~~~|__|~~~|__|~~~~~~~~~~~ + DATA ~~~~~~|_____X777777X666666X555555X444444X333333X222222X111111X000000X~~~~~~~ + <----> 840us(request to send by host) <---> 80us(hold DATA) + <--> 180us(clock low) + <---> 220us(clock high) + + +Protocol +-------- +COMMAND: + Inquiry 0x10 get key event with block + Instant 0x12 get key event + Model 0x14 get model number(M0110 responds with 0x09) + bit 7 1 if another device connected(used when keypad exists?) + bit4-6 next device model number + bit1-3 keyboard model number + bit 0 always 1 + Test 0x16 test(ACK:0x7D/NAK:0x77) + +KEY EVENT: + bit 7 key state(0:press 1:release) + bit 6-1 scan code(see below) + bit 0 always 1 + To get scan code use this: ((bits&(1<<7)) | ((bits&0x7F))>>1). + + Note: On the M0110A, Keypad keys and Arrow keys are preceded by 0x79. + Moreover, some Keypad keys(=, /, * and +) are preceded by 0x71 on press and 0xF1 on release. + +ARROW KEYS: + Arrow keys and Calc keys(+,*,/,= on keypad) share same byte sequence and preceding byte of + Calc keys(0x71 and 0xF1) means press and release event of SHIFT. This causes a very confusing situation, + it is difficult or impossible to tell Calc key from Arrow key plus SHIFT in some cases. + + Raw key events: + press release + ---------------- ---------------- + Left: 0x79, 0x0D 0x79, 0x8D + Right: 0x79, 0x05 0x79, 0x85 + Up: 0x79, 0x1B 0x79, 0x9B + Down: 0x79, 0x11 0x79, 0x91 + Pad+: 0x71, 0x79, 0x0D 0xF1, 0x79, 0x8D + Pad*: 0x71, 0x79, 0x05 0xF1, 0x79, 0x85 + Pad/: 0x71, 0x79, 0x1B 0xF1, 0x79, 0x9B + Pad=: 0x71, 0x79, 0x11 0xF1, 0x79, 0x91 + + +RAW CODE: + M0110A + ,---------------------------------------------------------. ,---------------. + | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Bcksp| |Clr| =| /| *| + |---------------------------------------------------------| |---------------| + |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| | | 7| 8| 9| -| + |-----------------------------------------------------' | |---------------| + |CapsLo| A| S| D| F| G| H| J| K| L| ;| '|Return| | 4| 5| 6| +| + |---------------------------------------------------------| |---------------| + |Shift | Z| X| C| V| B| N| M| ,| ,| /|Shft|Up | | 1| 2| 3| | + |---------------------------------------------------------' |-----------|Ent| + |Optio|Mac | Space | \|Lft|Rgt|Dn | | 0| .| | + `---------------------------------------------------------' `---------------' + ,---------------------------------------------------------. ,---------------. + | 65| 25| 27| 29| 2B| 2F| 2D| 35| 39| 33| 3B| 37| 31| 67| |+0F|*11|*1B|*05| + |---------------------------------------------------------| |---------------| + | 61| 19| 1B| 1D| 1F| 23| 21| 41| 45| 3F| 47| 43| 3D| | |+33|+37|+39|+1D| + |-----------------------------------------------------' | |---------------| + | 73| 01| 03| 05| 07| 0B| 09| 4D| 51| 4B| 53| 4F| 49| |+2D|+2F|+31|*0D| + |---------------------------------------------------------| |---------------| + | 71| 0D| 0F| 11| 13| 17| 5B| 5D| 27| 5F| 59| 71|+1B| |+27|+29|+2B| | + |---------------------------------------------------------' |-----------|+19| + | 75| 6F| 63 | 55|+0D|+05|+11| | +25|+03| | + `---------------------------------------------------------' `---------------' + + 0x79, 0xDD / 0xF1, 0xUU + * 0x71, 0x79,DD / 0xF1, 0x79, 0xUU + + +MODEL NUMBER: + M0110: 0x09 00001001 : model number 4 (100) + M0110A: 0x0B 00001011 : model number 5 (101) + M0110 & M0120: ??? + + +Scan Code +--------- + m0110_recv_key() function returns following scan codes instead of raw key events. + Scan codes are 1 byte long and MSB(bit7) is set when key is released. + + M0110 + ,---------------------------------------------------------. + | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backs| + |---------------------------------------------------------| + |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| \| + |---------------------------------------------------------| + |CapsLo| A| S| D| F| G| H| J| K| L| ;| '|Return| + |---------------------------------------------------------| + |Shift | Z| X| C| V| B| N| M| ,| ,| /| | + `---------------------------------------------------------' + |Opt|Mac | Space |Enter|Opt| + `------------------------------------------------' + ,---------------------------------------------------------. + | 32| 12| 13| 14| 15| 17| 16| 1A| 1C| 19| 1D| 1B| 18| 33| + |---------------------------------------------------------| + | 30| 0C| 0D| 0E| 0F| 10| 11| 20| 22| 1F| 23| 21| 1E| 2A| + |---------------------------------------------------------| + | 39| 00| 01| 02| 03| 05| 04| 26| 28| 25| 29| 27| 24| + |---------------------------------------------------------| + | 38| 06| 07| 08| 09| 0B| 2D| 2E| 2B| 2F| 2C| 38| + `---------------------------------------------------------' + | 3A| 37| 31 | 34| 3A| + `------------------------------------------------' + + M0110A + ,---------------------------------------------------------. ,---------------. + | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Bcksp| |Clr| =| /| *| + |---------------------------------------------------------| |---------------| + |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| | | 7| 8| 9| -| + |-----------------------------------------------------' | |---------------| + |CapsLo| A| S| D| F| G| H| J| K| L| ;| '|Return| | 4| 5| 6| +| + |---------------------------------------------------------| |---------------| + |Shift | Z| X| C| V| B| N| M| ,| ,| /|Shft|Up | | 1| 2| 3| | + |---------------------------------------------------------' |-----------|Ent| + |Optio|Mac | Space | \|Lft|Rgt|Dn | | 0| .| | + `---------------------------------------------------------' `---------------' + ,---------------------------------------------------------. ,---------------. + | 32| 12| 13| 14| 15| 17| 16| 1A| 1C| 19| 1D| 1B| 18| 33| | 47| 68| 6D| 62| + |---------------------------------------------------------| |---------------| + | 30| 0C| 0D| 0E| 0F| 10| 11| 20| 22| 1F| 23| 21| 1E| | | 59| 5B| 5C| 4E| + |-----------------------------------------------------' | |---------------| + | 39| 00| 01| 02| 03| 05| 04| 26| 28| 25| 29| 27| 24| | 56| 57| 58| 66| + |---------------------------------------------------------| |---------------| + | 38| 06| 07| 08| 09| 0B| 2D| 2E| 2B| 2F| 2C| 38| 4D| | 53| 54| 55| | + |---------------------------------------------------------' |-----------| 4C| + | 3A| 37| 31 | 2A| 46| 42| 48| | 52| 41| | + `---------------------------------------------------------' `---------------' + + +References +---------- +Technical Info for 128K/512K and Plus + ftp://ftp.apple.asimov.net/pub/apple_II/documentation/macintosh/Mac%20Hardware%20Info%20-%20Mac%20128K.pdf + ftp://ftp.apple.asimov.net/pub/apple_II/documentation/macintosh/Mac%20Hardware%20Info%20-%20Mac%20Plus.pdf +Protocol: + Page 20 of Tech Info for 128K/512K + http://www.mac.linux-m68k.org/devel/plushw.php +Connector: + Page 20 of Tech Info for 128K/512K + http://www.kbdbabel.org/conn/kbd_connector_macplus.png +Signaling: + http://www.kbdbabel.org/signaling/kbd_signaling_mac.png + http://typematic.blog.shinobi.jp/Entry/14/ +Scan Codes: + Page 22 of Tech Info for 128K/512K + Page 07 of Tech Info for Plus + http://m0115.web.fc2.com/m0110.jpg + http://m0115.web.fc2.com/m0110a.jpg +*/ diff --git a/m0110.h b/m0110.h index 287c45b548..2b95ed34d5 100644 --- a/m0110.h +++ b/m0110.h @@ -1,5 +1,5 @@ /* -Copyright 2011 Jun WAKO +Copyright 2011,2012 Jun WAKO This software is licensed with a Modified BSD License. All of this is supposed to be Free Software, Open Source, DFSG-free, @@ -54,23 +54,29 @@ POSSIBILITY OF SUCH DAMAGE. # error "M0110 data port setting is required in config.h" #endif -#define M0110_INQUIRY 0x10 -#define M0110_INSTANT 0x14 -#define M0110_MODEL 0x16 -#define M0110_TEST 0x36 +/* Commands */ +#define M0110_INQUIRY 0x10 +#define M0110_INSTANT 0x14 +#define M0110_MODEL 0x16 +#define M0110_TEST 0x36 -#define M0110_PAD 0x79 -#define M0110_NULL 0x7B -#define M0110_TEST_ACK 0x7D -#define M0110_TEST_NAK 0x77 +/* Response(raw byte from M0110) */ +#define M0110_NULL 0x7B +#define M0110_KEYPAD 0x79 +#define M0110_TEST_ACK 0x7D +#define M0110_TEST_NAK 0x77 +#define M0110_SHIFT 0x71 +#define M0110_ARROW_UP 0x1B +#define M0110_ARROW_DOWN 0x11 +#define M0110_ARROW_LEFT 0x0D +#define M0110_ARROW_RIGHT 0x05 +/* This inidcates no response. */ +#define M0110_ERROR 0xFF /* scan code offset for keypad and arrow keys */ #define M0110_KEYPAD_OFFSET 0x40 -#define M0110_ARROW_OFFSET 0x60 - -/* convert key event raw response into scan code */ -#define M0110_RAW2SCAN(key) ((key&(1<<7)) | ((key&0x7F)>>1)) +#define M0110_CALC_OFFSET 0x60 extern uint8_t m0110_error; @@ -80,5 +86,7 @@ void m0110_init(void); uint8_t m0110_send(uint8_t data); uint8_t m0110_recv(void); uint8_t m0110_recv_key(void); +uint8_t m0110_inquiry(void); +uint8_t m0110_instant(void); #endif diff --git a/m0110_usb/README b/m0110_usb/README deleted file mode 100644 index 6ef98757a3..0000000000 --- a/m0110_usb/README +++ /dev/null @@ -1,55 +0,0 @@ -M0110 to USB keyboard converter -=============================== -This firmware converts the protocol of Apple Macintosh keyboard M0110 into USB. - - -Connection ----------- -You need 4P4C plug and cable to connect Teensy into M0110. -Teensy port F0 is assigned for CLOCK line and F1 for DATA by default, you can change pin configuration with editing config.h.. - -Plug: - http://en.wikipedia.org/wiki/Modular_connector#4P4C - -Pinout: - http://www.kbdbabel.org/conn/kbd_connector_macplus.png - 1(Black): GND - 2(Red): CLOCK - 3(Green): DATA - 4(Yellow): +5V - - - -Build Frimware --------------- -Optionally edit Makefile and config.h for build options, pin configuration or MCU. - -$ cd m0110_usb -$ make -and program your Teensy with loader. - - - -Keymap ------- -You can change a keymap by editing code of keymap.c like following. -How to define the keymap is probably obvious. You can find key symbols in usb_keycodes.h. - -This is a default keymap for M0110. -,---------------------------------------------------------. -| `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Bacpa| -|---------------------------------------------------------| -|Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| \| -|---------------------------------------------------------| -|CapsLo| A| S| D| F| G| H| J| K| L| ;| '|Return| -|---------------------------------------------------------| -|Shift | Z| X| C| V| B| N| M| ,| ,| /|Shift | -`---------------------------------------------------------' - |Opt|Alt | Space |Alt |Opt| - `-----------------------------------------------' - - -Notes ------ - -EOF diff --git a/m0110_usb/README.md b/m0110_usb/README.md new file mode 100644 index 0000000000..92b58f684a --- /dev/null +++ b/m0110_usb/README.md @@ -0,0 +1,126 @@ +M0110/M0110A to USB keyboard converter +====================================== +This firmware converts the protocol of Apple Macintosh keyboard M0110/M0110A into USB. +Target board of this project is [PJRC Teensy](http://www.pjrc.com/teensy/), though, +you can use other board with USB AVR like `ATmega32U4` and `AT90USB`. + +![M0110](https://github.com/tmk/tmk_keyboard/raw/master/m0110_usb/doc/m0110.jpg) + +M0110A support was contributed by [skagon@github](https://github.com/skagon). + + + +Connection +---------- +You need 4P4C plug and cable to connect Teensy or other AVR dev board into the keyboard. +Teensy port `PF0` is assigned for `CLOCK` line and `PF1` for `DATA` by default, +you can change pin configuration with editing *config.h*. + +You can find 4P4C plugs on telephone handset cable. Note that it is *crossover* connection +while Macintosh keyboard cable is *straight*. + +[![Conection](http://i.imgur.com/vJoVOm.jpg)](http://i.imgur.com/vJoVO.jpg) + +In this pic: + +1. `GND`(Black) +2. `CLOCK`(Red) +3. `DATA`(Green) +4. `+5V`(Yellow) + +Not that wire colors may vary in your cable. + + +### Pinout +- +- + +![Jack fig](http://www.kbdbabel.org/conn/kbd_connector_macplus.png) + + +### Pull-up Registor +You may need pull-up registors on signal lines(`CLOCK`, `DATA`) in particular +when you have long or coiled cable. 1k-10k Ohm will be OK for this purpose. +In some cases MCU can't read signal from keyboard correctly without pull-up resistors. + + + +Building Frimware +----------------- +To compile firmware you need AVR GCC. You can use [WinAVR](http://winavr.sourceforge.net/) on Windows. +You can edit *Makefile* and *config.h* to change compile options and pin configuration. + + $ git clone ... (or download source) + $ cd m0110_usb + $ make + +and program your Teensy with [PJRC Teensy loader](http://www.pjrc.com/teensy/loader.html). + + + +Keymap +------ +You can change keymaps by editing *keymap.c*. + +### M0110 +#### *Default* + ,---------------------------------------------------------. + | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backs| + |---------------------------------------------------------| + |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| \| + |---------------------------------------------------------| + |Fn0 | A| S| D| F| G| H| J| K| L| ;| '|Return| + |---------------------------------------------------------| + |Shift | Z| X| C| V| B| N| M| ,| ,| /|Shift | + `---------------------------------------------------------' + |Ctr|Alt | Space |Gui |Ctr| + `-----------------------------------------------' + You can register Esc by hitting(press&release) Fn0 quickly. + +#### *HHKB/WASD cursor Layer(Fn0)* + ,---------------------------------------------------------. + |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Delet| + |---------------------------------------------------------| + |Caps |Hom| Up|PgU| | | | |Psc|Slk|Pau|Up |Ins| \| + |---------------------------------------------------------| + |Fn0 |Lef|Dow|Rig| | | | |Hom|PgU|Lef|Rig|Return| + |---------------------------------------------------------| + |Shift |End| |PgD| |VoD|VoU|Mut|End|PgD|Dow|Shift | + `---------------------------------------------------------' + |Ctr|Alt | Space |Gui |Ctr| + `-----------------------------------------------' + +### M0110A +#### *Default* + ,---------------------------------------------------------. ,---------------. + | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backs| |Gui| =| /| *| + |---------------------------------------------------------| |---------------| + |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| | | 7| 8| 9| -| + |-----------------------------------------------------' | |---------------| + |Fn0 | A| S| D| F| G| H| J| K| L| ;| '|Return| | 4| 5| 6| +| + |---------------------------------------------------------| |---------------| + |Shift | Z| X| C| V| B| N| M| ,| ,| /|Shft|Up | | 1| 2| 3| | + |---------------------------------------------------------| |-----------|Ent| + |Ctrl |Alt | Space | \|Lft|Rgt|Dn | | 0| .| | + `---------------------------------------------------------' `---------------' +#### *HHKB/WASD cursor Layer(Fn0)* + ,---------------------------------------------------------. ,---------------. + |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Delet| |Nlk|Mb1|Mb3|Mb2| + |---------------------------------------------------------| |---------------| + |Caps |Hom| Up|PgU| | | | |Psc|Slk|Pau|Up |Ins| | |MwD|McU|MwU|MwU| + |-----------------------------------------------------' | |---------------| + |Fn0 |Lef|Dow|Rig| | | | |Hom|PgU|Lef|Rig|Return| |McL|McD|McR|MwD| + |---------------------------------------------------------| |---------------| + |Shift |End| |PgD| |VoD|VoU|Mut|End|PgD|Dow|Shif|Up | |MwL|McD|MwR| | + |---------------------------------------------------------| |-----------|Mb2| + |Ctrl |Alt | Space |Gui | \|Lft|Rgt|Dn | | Mb1|Mb3| | + `---------------------------------------------------------' `---------------' + + + +Debug +----- +You can use [PJRC HID listen](http://www.pjrc.com/teensy/hid_listen.html) to see debug output. + +The converter has some functions for debug, press `Alt+Gui+H` simultaneously to get help. +These function is totally undocumented, tentative, inconsistent and buggy. diff --git a/m0110_usb/config.h b/m0110_usb/config.h index c12e0738da..4563d6da54 100644 --- a/m0110_usb/config.h +++ b/m0110_usb/config.h @@ -1,5 +1,5 @@ /* -Copyright 2011 Jun Wako +Copyright 2011,2012 Jun Wako This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by @@ -30,7 +30,7 @@ along with this program. If not, see . /* matrix size */ -#define MATRIX_ROWS 8 +#define MATRIX_ROWS 14 #define MATRIX_COLS 8 /* Locking Caps Lock support */ @@ -38,8 +38,7 @@ along with this program. If not, see . /* key combination for command */ #define IS_COMMAND() ( \ - keyboard_report->mods == (MOD_BIT(KB_LSHIFT) | MOD_BIT(KB_LCTRL) | MOD_BIT(KB_LALT) | MOD_BIT(KB_LGUI)) || \ - keyboard_report->mods == (MOD_BIT(KB_LSHIFT) | MOD_BIT(KB_RSHIFT)) \ + keyboard_report->mods == (MOD_BIT(KB_LALT) | MOD_BIT(KB_LGUI)) \ ) diff --git a/m0110_usb/doc/m0110.jpg b/m0110_usb/doc/m0110.jpg old mode 100755 new mode 100644 diff --git a/m0110_usb/doc/teensy.jpg b/m0110_usb/doc/teensy.jpg old mode 100755 new mode 100644 diff --git a/m0110_usb/keymap.c b/m0110_usb/keymap.c index bbb699a9ac..939010c6d0 100644 --- a/m0110_usb/keymap.c +++ b/m0110_usb/keymap.c @@ -1,5 +1,5 @@ /* -Copyright 2011 Jun Wako +Copyright 2011,2012 Jun Wako This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by @@ -14,10 +14,8 @@ GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program. If not, see . */ +/* M0110A Support was contributed by skagon@github */ -/* - * Keymap for ADB keyboard - */ #include #include #include @@ -31,16 +29,12 @@ along with this program. If not, see . #define KEYCODE(layer, row, col) (pgm_read_byte(&keymaps[(layer)][(row)][(col)])) -// Convert physical keyboard layout to matrix array. -// This is a macro to define keymap easily in keyboard layout form. -// TODO: layout for M0110A -/* M0110 */ #define KEYMAP( \ - K32,K12,K13,K14,K15,K17,K16,K1A,K1C,K19,K1D,K1B,K18,K33, \ - K30,K0C,K0D,K0E,K0F,K11,K10,K20,K22,K1F,K23,K21,K1E,K2A, \ - K39,K00,K01,K02,K03,K05,K04,K26,K28,K25,K29,K27, K24, \ - K38,K06,K07,K08,K09,K0B,K2D,K2E,K2B,K2F,K2C, \ - K3A,K37, K31, K34 \ + K32,K12,K13,K14,K15,K17,K16,K1A,K1C,K19,K1D,K1B,K18,K33, K47,K68,K6D,K62, \ + K30,K0C,K0D,K0E,K0F,K11,K10,K20,K22,K1F,K23,K21,K1E, K59,K5B,K5C,K4E, \ + K39,K00,K01,K02,K03,K05,K04,K26,K28,K25,K29,K27, K24, K56,K57,K58,K66, \ + K38,K06,K07,K08,K09,K0B,K2D,K2E,K2B,K2F,K2C, K4D, K53,K54,K55,K4C, \ + K3A,K37, K31, K34,K2A,K46,K42,K48, K52, K41 \ ) { \ { KB_##K00, KB_##K01, KB_##K02, KB_##K03, KB_##K04, KB_##K05, KB_##K06, KB_##K07 }, \ { KB_##K08, KB_##K09, KB_NO, KB_##K0B, KB_##K0C, KB_##K0D, KB_##K0E, KB_##K0F }, \ @@ -49,7 +43,13 @@ along with this program. If not, see . { KB_##K20, KB_##K21, KB_##K22, KB_##K23, KB_##K24, KB_##K25, KB_##K26, KB_##K27 }, \ { KB_##K28, KB_##K29, KB_##K2A, KB_##K2B, KB_##K2C, KB_##K2D, KB_##K2E, KB_##K2F }, \ { KB_##K30, KB_##K31, KB_##K32, KB_##K33, KB_##K34, KB_NO, KB_NO, KB_##K37 }, \ - { KB_##K38, KB_##K39, KB_##K3A, KB_NO, KB_NO, KB_NO, KB_NO, KB_NO } \ + { KB_##K38, KB_##K39, KB_##K3A, KB_NO, KB_NO, KB_NO, KB_NO, KB_NO }, \ + { KB_NO, KB_##K41, KB_##K42, KB_NO, KB_NO, KB_NO, KB_##K46, KB_##K47 }, \ + { KB_##K48, KB_NO, KB_NO, KB_NO, KB_##K4C, KB_##K4D, KB_##K4E, KB_NO }, \ + { KB_NO, KB_NO, KB_##K52, KB_##K53, KB_##K54, KB_##K55, KB_##K56, KB_##K57 }, \ + { KB_##K58, KB_##K59, KB_NO, KB_##K5B, KB_##K5C, KB_NO, KB_NO, KB_NO }, \ + { KB_NO, KB_NO, KB_##K62, KB_NO, KB_NO, KB_NO, KB_##K66, KB_NO }, \ + { KB_##K68, KB_NO, KB_NO, KB_NO, KB_NO, KB_##K6D, KB_NO, KB_NO }, \ } @@ -58,7 +58,7 @@ static const uint8_t PROGMEM fn_layer[] = { 1, // Fn0 2, // Fn1 3, // Fn2 - 0, // Fn3 + 1, // Fn3 0, // Fn4 0, // Fn5 0, // Fn6 @@ -68,10 +68,17 @@ static const uint8_t PROGMEM fn_layer[] = { // Assign Fn key(0-7) to a keycode sent when release Fn key without use of the layer. // See layer.c for details. static const uint8_t PROGMEM fn_keycode[] = { - KB_SCOLON, // Fn0 - KB_SLASH, // Fn1 +#ifndef HASU + KB_ESC, // Fn0 + KB_NO, // Fn1 KB_NO, // Fn2 KB_NO, // Fn3 +#else + KB_NO, // Fn0 + KB_SCOLON, // Fn1 + KB_SLASH, // Fn2 + KB_UP, // Fn3 +#endif KB_NO, // Fn4 KB_NO, // Fn5 KB_NO, // Fn6 @@ -79,52 +86,100 @@ static const uint8_t PROGMEM fn_keycode[] = { }; static const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { - // LShift and RShift are logically same one button. - // LOption and ROption are logically same one button. - /* Default Layer: plain keymap - * ,---------------------------------------------------------. - * | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Bacpa| - * |---------------------------------------------------------| - * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| \| - * |---------------------------------------------------------| - * |Contro| A| S| D| F| G| H| J| K| L|Fn0| '|Return| - * |---------------------------------------------------------| - * |Shift | Z| X| C| V| B| N| M| ,| ,|Fn1| Shift| - * `---------------------------------------------------------' - * |Fn2|Alt | Space |Gui |Fn2| - * `-----------------------------------------------' + /* + * The keymap works with both M0110 and M0110A keyboards. As you can see, the M0110A is a superset + * of the M0110 keyboard, with only one exception: 'Enter' in M0110 does not exist + * on the M0110A, but since it generates a unique scan code which is not used for some other key in + * the M0110A, they are totally interchangeable. In fact, the M0110A is functionally (almost) + * identical to the combination of the M0110 along with the M0120 keypad. The only difference + * (which is causing some problems as you will read below) is that the M0110+M0120 don't have + * dedicated arrow keys, while the M0110A does. However, the M0120 did have arrow keys, which + * doubled as the [comma], [/], [*] and [+] keys, when used with the [Shift] key. The M0110A has + * substituted the [comma] key with the [=] key, however its scancode is the same. + * + * Default: + * ,---------------------------------------------------------. ,---------------. + * | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backs| |Gui| =| /| *| + * |---------------------------------------------------------| |---------------| + * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| | | 7| 8| 9| -| + * |-----------------------------------------------------' | |---------------| + * |Fn0 | A| S| D| F| G| H| J| K| L| ;| '|Return| | 4| 5| 6| +| + * |---------------------------------------------------------| |---------------| + * |Shift | Z| X| C| V| B| N| M| ,| ,| /|Shft|Up | | 1| 2| 3| | + * |---------------------------------------------------------| |-----------|Ent| + * |Ctrl |Alt | Space |Gui| \|Lft|Rgt|Dn | | 0| .| | + * `---------------------------------------------------------' `---------------' + * + * HHKB/WASD/Mouse Layer(Fn0): + * ,---------------------------------------------------------. ,---------------. + * |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Delet| |Nlk|Mb1|Mb3|Mb2| + * |---------------------------------------------------------| |---------------| + * |Caps |Hom| Up|PgU| | | | |Psc|Slk|Pau|Up |Ins| | |MwD|McU|MwU|MwU| + * |-----------------------------------------------------' | |---------------| + * |Fn0 |Lef|Dow|Rig| | | | |Hom|PgU|Lef|Rig|Return| |McL|McD|McR|MwD| + * |---------------------------------------------------------| |---------------| + * |Shift |End| |PgD| |VoD|VoU|Mut|End|PgD|Dow|Shif|Up | |MwL|McD|MwR| | + * |---------------------------------------------------------| |-----------|Mb2| + * |Ctrl |Alt | Space |Gui | \|Lft|Rgt|Dn | | Mb1|Mb3| | + * `---------------------------------------------------------' `---------------' + * Mb: Mouse Button / Mc: Mouse Cursor / Mw: Mouse Wheel + * + * NOTE: You can register Esc by hitting(press&release) Fn0 quickly. + * NOTE: Gui between Space and \ is Enter on M0110 not exists on M0110A. + * NOTE: LShift and RShift are logically same key. (M0110, M0110A) + * NOTE: LOption and ROption are logically same key. (M0110) */ +#ifndef HASU KEYMAP( - GRV, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, MINS,EQL, BSPC, - TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC,RBRC,BSLS, - LCTL,A, S, D, F, G, H, J, K, L, FN0, QUOT, ENT, - LSFT,Z, X, C, V, B, N, M, COMM,DOT, FN1, - FN2, LALT, SPC, LGUI - ), - // vi mousekeys - KEYMAP( - ESC, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, DEL, - CAPS,NO, NO, NO, NO, NO, WH_L,WH_D,WH_U,WH_R,NO, NO, NO, NO, - LCTL,VOLD,VOLU,MUTE,NO, NO, MS_L,MS_D,MS_U,MS_R,FN0, NO, ENT, - LSFT,NO, NO, NO, NO, BTN3,BTN2,BTN1,NO, NO, NO, - NO, LALT, BTN1, LGUI - ), - // vi cusorkeys - KEYMAP( - ESC, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, DEL, - CAPS,NO, NO, NO, NO, NO, HOME,PGDN,PGUP,END, NO, NO, NO, NO, - LCTL,NO, NO, NO, NO, NO, LEFT,DOWN,UP, RGHT,NO, NO, ENT, - LSFT,NO, NO, NO, NO, NO, HOME,PGDN,PGUP,END, FN1, - NO, LALT, SPC, LGUI + GRV, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, MINS,EQL, BSPC, LGUI,EQL, PSLS,PAST, + TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC,RBRC, P7, P8, P9, PMNS, + FN0, A, S, D, F, G, H, J, K, L, SCLN,QUOT, ENT, P4, P5, P6, PPLS, + LSFT,Z, X, C, V, B, N, M, COMM,DOT, SLSH, UP, P1, P2, P3, PENT, + LCTL,LALT, SPC, LGUI,BSLS,LEFT,RGHT,DOWN, P0, PDOT ), // HHKB & WASD KEYMAP( - ESC, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, DEL, - CAPS,HOME,UP, PGUP,NO, NO, NO, NO, PSCR,SLCK,BRK, UP, NO, NO, - LCTL,LEFT,DOWN,RGHT,NO, NO, NO, NO, HOME,PGUP,LEFT,RGHT, ENT, - LSFT,END, NO, PGDN,NO, VOLD,VOLU,MUTE,END, PGDN,DOWN, - FN2, LALT, SPC, LGUI + ESC, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, DEL, NLCK,BTN1,BTN3,BTN2, + CAPS,HOME,UP, PGUP,NO, NO, NO, NO, PSCR,SLCK,BRK, UP, INS, WH_D,MS_U,WH_U,WH_U, + FN0, LEFT,DOWN,RGHT,NO, NO, NO, NO, HOME,PGUP,LEFT,RGHT, ENT, MS_L,MS_D,MS_R,WH_D, + LSFT,END, NO, PGDN,NO, VOLD,VOLU,MUTE,END, PGDN,DOWN, UP, WH_L,MS_D,WH_R,BTN2, + LCTL,LALT, SPC, LGUI,BSLS,LEFT,RGHT,DOWN, BTN1, BTN3 ), +#else + // hasu's keymap + // To enable use this 'make' option: make EXTRAFLAGS=-DHASU + KEYMAP( + ESC, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, MINS,EQL, BSPC, LGUI,EQL, PSLS,PAST, + TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC,RBRC, P7, P8, P9, PMNS, + LCTL,A, S, D, F, G, H, J, K, L, FN1, QUOT, ENT, P4, P5, P6, PPLS, + LSFT,Z, X, C, V, B, N, M, COMM,DOT, FN2, FN3, P1, P2, P3, PENT, + LCTL,LALT, SPC, LGUI,BSLS,LEFT,RGHT,DOWN, LGUI, PDOT + ), + // HHKB & WASD + KEYMAP( + GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, DEL, NLCK,EQL, PSLS,PAST, + CAPS,HOME,UP, PGUP,NO, NO, NO, NO, PSCR,SLCK,BRK, UP, INS, P7, P8, P9, PMNS, + LCTL,LEFT,DOWN,RGHT,NO, NO, NO, NO, HOME,PGUP,LEFT,RGHT, ENT, P4, P5, P6, PPLS, + LSFT,END, NO, PGDN,NO, VOLD,VOLU,MUTE,END, PGDN,DOWN, FN3, P1, P2, P3, PENT, + LCTL,LALT, SPC, LGUI,BSLS,LEFT,RGHT,DOWN, P0, PDOT + ), + // vi mousekeys + KEYMAP( + GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, DEL, NLCK,EQL, PSLS,PAST, + CAPS,NO, NO, NO, NO, NO, WH_L,WH_D,WH_U,WH_R,NO, NO, NO, P7, P8, P9, PMNS, + NO, VOLD,VOLU,MUTE,NO, NO, MS_L,MS_D,MS_U,MS_R,FN1, NO, ENT, P4, P5, P6, PPLS, + LSFT,NO, NO, NO, NO, BTN3,BTN2,BTN1,NO, NO, NO, UP, P1, P2, P3, PENT, + LCTL,LALT, BTN1, LGUI,BSLS,LEFT,RGHT,DOWN, P0, PDOT + ), + // vi cusorkeys + KEYMAP( + GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, DEL, NLCK,EQL, PSLS,PAST, + CAPS,NO, NO, NO, NO, NO, HOME,PGDN,PGUP,END, NO, NO, NO, P7, P8, P9, PMNS, + NO, NO, NO, NO, NO, NO, LEFT,DOWN,UP, RGHT,NO, NO, ENT, P4, P5, P6, PPLS, + LSFT,NO, NO, NO, NO, NO, HOME,PGDN,PGUP,END, FN2, UP, P1, P2, P3, PENT, + LCTL,LALT, SPC, LGUI,BSLS,LEFT,RGHT,DOWN, P0, PDOT + ), +#endif }; diff --git a/m0110_usb/matrix.c b/m0110_usb/matrix.c index f045920ccd..1ca6894c44 100644 --- a/m0110_usb/matrix.c +++ b/m0110_usb/matrix.c @@ -1,5 +1,5 @@ /* -Copyright 2011 Jun Wako +Copyright 2011,2012 Jun Wako This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by @@ -32,7 +32,7 @@ along with this program. If not, see . #define CAPS 0x39 -#define CAPS_UP (CAPS | 0x80) +#define CAPS_BREAK (CAPS | 0x80) #define ROW(key) ((key)>>3&0x0F) #define COL(key) ((key)&0x07) @@ -43,9 +43,6 @@ static bool is_modified = false; static uint8_t *matrix; static uint8_t _matrix0[MATRIX_ROWS]; -#ifdef MATRIX_HAS_GHOST -static bool matrix_has_ghost_in_row(uint8_t row); -#endif static void register_key(uint8_t key); @@ -88,11 +85,13 @@ uint8_t matrix_scan(void) // Send Caps key up event if (matrix_is_on(ROW(CAPS), COL(CAPS))) { is_modified = true; - register_key(CAPS_UP); + register_key(CAPS_BREAK); } #endif if (key == M0110_NULL) { return 0; + } else if (key == M0110_ERROR) { + return 0; } else { #ifdef MATRIX_HAS_LOCKING_CAPS if (host_keyboard_leds() & (1<