1
0
Fork 0

Properly always copy firmware

This finishes fixing #2314, which mostly copies the firmware when compiling.
However, it misses `:teensy`, `:avrdude` and most importantly, `:production`
This commit is contained in:
U-LANDSRAAD\drashna 2018-03-29 12:26:09 -07:00 committed by Jack Humbert
parent fb34fdbbc9
commit c2bec5b3f0

View file

@ -9,7 +9,7 @@ SIZE = avr-size
AR = avr-ar rcs
NM = avr-nm
HEX = $(OBJCOPY) -O $(FORMAT) -R .eeprom -R .fuse -R .lock -R .signature
EEP = $(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" --change-section-lma .eeprom=0 --no-change-warnings -O $(FORMAT)
EEP = $(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" --change-section-lma .eeprom=0 --no-change-warnings -O $(FORMAT)
BIN =
COMMON_VPATH += $(DRIVER_PATH)/avr
@ -124,16 +124,16 @@ qmk: $(BUILD_DIR)/$(TARGET).hex
program: $(BUILD_DIR)/$(TARGET).hex $(BUILD_DIR)/$(TARGET).eep check-size
$(PROGRAM_CMD)
teensy: $(BUILD_DIR)/$(TARGET).hex check-size
teensy: $(BUILD_DIR)/$(TARGET).hex check-size cpfirmware
$(TEENSY_LOADER_CLI) -mmcu=$(MCU) -w -v $(BUILD_DIR)/$(TARGET).hex
BATCHISP ?= batchisp
BATCHISP ?= batchisp
flip: $(BUILD_DIR)/$(TARGET).hex check-size
$(BATCHISP) -hardware usb -device $(MCU) -operation erase f
$(BATCHISP) -hardware usb -device $(MCU) -operation loadbuffer $(BUILD_DIR)/$(TARGET).hex program
$(BATCHISP) -hardware usb -device $(MCU) -operation start reset 0
DFU_PROGRAMMER ?= dfu-programmer
GREP ?= grep
@ -169,7 +169,7 @@ dfu-ee: $(BUILD_DIR)/$(TARGET).hex $(BUILD_DIR)/$(TARGET).eep
fi
$(DFU_PROGRAMMER) $(MCU) reset
avrdude: $(BUILD_DIR)/$(TARGET).hex check-size
avrdude: $(BUILD_DIR)/$(TARGET).hex check-size cpfirmware
if $(GREP) -q -s Microsoft /proc/version; then \
echo 'ERROR: AVR flashing cannot be automated within the Windows Subsystem for Linux (WSL) currently. Instead, take the .hex file generated and flash it using AVRDUDE, AVRDUDESS, or XLoader.'; \
else \
@ -199,7 +199,7 @@ bin: $(BUILD_DIR)/$(TARGET).hex
# copy bin to FLASH.bin
flashbin: bin
$(COPY) $(BUILD_DIR)/$(TARGET).bin FLASH.bin;
$(COPY) $(BUILD_DIR)/$(TARGET).bin FLASH.bin;
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
@ -250,7 +250,7 @@ extcoff: $(BUILD_DIR)/$(TARGET).elf
@$(SECHO) $(MSG_EXTENDED_COFF) $(BUILD_DIR)/$(TARGET).cof
$(COFFCONVERT) -O coff-ext-avr $< $(BUILD_DIR)/$(TARGET).cof
bootloader:
bootloader:
make -C lib/lufa/Bootloaders/DFU/ clean
echo -e "#ifndef QMK_KEYBOARD\n#define QMK_KEYBOARD\n" > lib/lufa/Bootloaders/DFU/Keyboard.h
echo -e `$(GREP) "MANUFACTURER" $(ALL_CONFIGS) -h | tail -1` >> lib/lufa/Bootloaders/DFU/Keyboard.h
@ -264,7 +264,7 @@ bootloader:
echo -e "BootloaderDFU.hex copied to $(TARGET)_bootloader.hex"
cp lib/lufa/Bootloaders/DFU/BootloaderDFU.hex $(TARGET)_bootloader.hex
production: $(BUILD_DIR)/$(TARGET).hex bootloader
production: $(BUILD_DIR)/$(TARGET).hex bootloader cpfirmware
@cat $(BUILD_DIR)/$(TARGET).hex | awk '/^:00000001FF/ == 0' > $(TARGET)_production.hex
@cat $(TARGET)_bootloader.hex >> $(TARGET)_production.hex
echo "File sizes:"