1
0
Fork 0

Cleanup rules.mk for 32U4 keyboards, L-M (#7120)

* Cleanup rules.mk for 32U4 keyboards, L-M

* Move some stuff to keyboard level
This commit is contained in:
fauxpark 2019-10-25 07:50:13 +11:00 committed by Drashna Jaelre
parent 335dd0271e
commit e96cac0814
58 changed files with 269 additions and 1481 deletions

View file

@ -1,46 +1,18 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Processor frequency
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 8000000 F_CPU = 8000000
# # Bootloader selection
# LUFA specific # Teensy halfkay
# # Pro Micro caterina
# Target architecture (see library "Board Types" documentation). # Atmel DFU atmel-dfu
ARCH = AVR8 # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
# Input clock frequency. # ATmega32A bootloadHID
# This will define a symbol, F_USB, in all source code files equal to the # ATmega328P USBasp
# input clock frequency (before any prescaling is performed) in Hz. This value may BOOTLOADER = caterina
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Bootloader
# This definition is optional, and if your keyboard supports multiple bootloaders of
# different sizes, comment this out, and the correct address will be loaded
# automatically (+60). See bootloader.mk for all options.
BOOTLOADER = catarina
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Build Options # Build Options
# change to "no" to disable the options, or define them in the Makefile in # change to "no" to disable the options, or define them in the Makefile in

View file

@ -1,22 +0,0 @@
# Build Options
# change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically
#
BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = no # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = no # Console for debug(+400)
COMMAND_ENABLE = no # Commands for debug and configuration
NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality
MIDI_ENABLE = no # MIDI controls
AUDIO_ENABLE = no # Audio output on port C6
UNICODE_ENABLE = no # Unicode
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight.
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend

View file

@ -1 +1 @@
RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight. RGBLIGHT_ENABLE = yes

View file

@ -1,3 +0,0 @@
BACKLIGHT_ENABLE = no
RGBLIGHT_ENABLE = no
AUDIO_ENABLE = no

View file

@ -1,47 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Bootloader
# This definition is optional, and if your keyboard supports multiple bootloaders of
# different sizes, comment this out, and the correct address will be loaded
# automatically (+60). See bootloader.mk for all options.
BOOTLOADER = caterina BOOTLOADER = caterina
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Build Options # Build Options
# change to "no" to disable the options, or define them in the Makefile in # change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically # the appropriate keymap folder that will get included automatically
@ -50,8 +19,8 @@ BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = no # Mouse keys(+4700) MOUSEKEY_ENABLE = no # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450) EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = no # Console for debug(+400) CONSOLE_ENABLE = no # Console for debug(+400)
COMMAND_ENABLE = yes # Commands for debug and configuration COMMAND_ENABLE = no # Commands for debug and configuration
NKRO_ENABLE = no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality
MIDI_ENABLE = no # MIDI controls MIDI_ENABLE = no # MIDI controls
AUDIO_ENABLE = no # Audio output on port C6 AUDIO_ENABLE = no # Audio output on port C6

View file

@ -1,50 +1,14 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# Build Options # Build Options

View file

@ -1,41 +1,14 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# Build Options # Build Options

View file

@ -1,41 +1,14 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# Build Options # Build Options

View file

@ -1 +0,0 @@
BACKLIGHT_ENABLE = no

View file

@ -1 +0,0 @@
BACKLIGHT_ENABLE = no

View file

@ -1,50 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Build Options # Build Options
# change to "no" to disable the options, or define them in the Makefile in # change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically # the appropriate keymap folder that will get included automatically

View file

@ -1,4 +1,2 @@
BOOTLOADER = atmel-dfu
BACKLIGHT_ENABLE = yes BACKLIGHT_ENABLE = yes
RGBLIGHT_ENABLE = yes RGBLIGHT_ENABLE = yes

View file

@ -1,48 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Bootloader
# This definition is optional, and if your keyboard supports multiple bootloaders of
# different sizes, comment this out, and the correct address will be loaded
# automatically (+60). See bootloader.mk for all options.
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Build Options # Build Options
# change to "no" to disable the options, or define them in the Makefile in # change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically # the appropriate keymap folder that will get included automatically

View file

@ -6,15 +6,3 @@ BOOT_LOADER = BootloaderHID
# Extra source files for IS3731 lighting # Extra source files for IS3731 lighting
SRC = TWIlib.c issi.c lighting.c SRC = TWIlib.c issi.c lighting.c
# Processor frequency.
F_CPU = 16000000
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT

View file

@ -1,14 +1,15 @@
SRC = TWIlib.c issi.c lighting.c # MCU name
MCU = atmega32u4 MCU = atmega32u4
OPT_DEFS += -DBOOTLOADER_SIZE=4096
F_CPU = 16000000 # Bootloader selection
F_USB = $(F_CPU) # Teensy halfkay
ARCH = AVR8 # Pro Micro caterina
# Atmel DFU atmel-dfu
# Interrupt driven control endpoint task(+60) # LUFA DFU lufa-dfu
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT # QMK DFU qmk-dfu
# ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu
LAYOUTS = numpad_6x4 LAYOUTS = numpad_6x4
@ -31,6 +32,7 @@ TAP_DANCE_ENABLE = no
ISSI_ENABLE = yes # If the I2C pullup resistors aren't install this must be disabled ISSI_ENABLE = yes # If the I2C pullup resistors aren't install this must be disabled
WATCHDOG_ENABLE = no # Resets keyboard if matrix_scan isn't run every 250ms WATCHDOG_ENABLE = no # Resets keyboard if matrix_scan isn't run every 250ms
SRC = TWIlib.c issi.c lighting.c
ifeq ($(strip $(ISSI_ENABLE)), yes) ifeq ($(strip $(ISSI_ENABLE)), yes)
TMK_COMMON_DEFS += -DISSI_ENABLE TMK_COMMON_DEFS += -DISSI_ENABLE

View file

@ -1,3 +1,3 @@
SRC += rev1/matrix.c SRC += rev1/matrix.c
SRC += rev1/split_util.c SRC += rev1/split_util.c
SRC += rev1/split_scomm.c SRC += rev1/split_scomm.c

View file

@ -1,57 +1,16 @@
SRC += i2c.c
SRC += serial.c
SRC += ssd1306.c
# if firmware size over limit, try this option
# CFLAGS += -flto
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Build Options # Build Options
# change to "no" to disable the options, or define them in the Makefile in # change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically # the appropriate keymap folder that will get included automatically
@ -73,4 +32,11 @@ SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
CUSTOM_MATRIX = yes CUSTOM_MATRIX = yes
SRC += i2c.c
SRC += serial.c
SRC += ssd1306.c
# if firmware size over limit, try this option
# CFLAGS += -flto
DEFAULT_FOLDER = lily58/rev1 DEFAULT_FOLDER = lily58/rev1

View file

@ -1,49 +1,15 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to BOOTLOADER = atmel-dfu
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change to "no" to disable the options, or define them in the Makefile in # change to "no" to disable the options, or define them in the Makefile in

View file

@ -1,3 +1,2 @@
NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
RGBLIGHT_ENABLE = no # Enable keyboard underlight functionality (+4870) RGBLIGHT_ENABLE = no # Enable keyboard underlight functionality (+4870)

View file

@ -1,51 +1,15 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to BOOTLOADER = qmk-dfu
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
BOOTLOADER= qmk-dfu
# Build Options # Build Options
# comment out to disable the options. # comment out to disable the options.
@ -62,4 +26,3 @@ UNICODE_ENABLE = no # Unicode
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
DEFAULT_FOLDER = maartenwut/atom47/rev3 DEFAULT_FOLDER = maartenwut/atom47/rev3

View file

@ -3,4 +3,3 @@ SRC += keyboards/wilba_tech/wt_main.c
RAW_ENABLE = yes RAW_ENABLE = yes
DYNAMIC_KEYMAP_ENABLE = yes DYNAMIC_KEYMAP_ENABLE = yes

View file

@ -1,50 +1,15 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to BOOTLOADER = qmk-dfu
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# comment out to disable the options. # comment out to disable the options.
@ -63,4 +28,3 @@ UNICODE_ENABLE = no # Unicode
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
LAYOUTS = 60_ansi 60_ansi_split_bs_rshift 60_hhkb 60_iso 60_tsangan_hhkb LAYOUTS = 60_ansi 60_ansi_split_bs_rshift 60_hhkb 60_iso 60_tsangan_hhkb

View file

@ -1,49 +1,14 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
BOOTLOADER = qmk-dfu BOOTLOADER = qmk-dfu
# Build Options # Build Options

View file

@ -1,63 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = qmk-dfu BOOTLOADER = qmk-dfu
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #

View file

@ -1,42 +1,14 @@
# MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
BOOTLOADER = qmk-dfu BOOTLOADER = qmk-dfu
# Build Options # Build Options

View file

@ -1,58 +1,12 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096

View file

@ -1,58 +1,12 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = halfkay BOOTLOADER = halfkay
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096

View file

@ -1,10 +1,14 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Bootloader # Bootloader selection
# This definition is optional, and if your keyboard supports multiple bootloaders of # Teensy halfkay
# different sizes, comment this out, and the correct address will be loaded # Pro Micro caterina
# automatically (+60). See bootloader.mk for all options. # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
# ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# Build Options # Build Options
@ -27,4 +31,3 @@ RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight.
KEY_LOCK_ENABLE = yes KEY_LOCK_ENABLE = yes
API_SYSEX_ENABLE = no API_SYSEX_ENABLE = no
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend

View file

@ -1,15 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Bootloader # Bootloader selection
# This definition is optional, and if your keyboard supports multiple bootloaders of # Teensy halfkay
# different sizes, comment this out, and the correct address will be loaded # Pro Micro caterina
# automatically (+60). See bootloader.mk for all options. # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
# ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Build Options # Build Options
# change to "no" to disable the options, or define them in the Makefile in # change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically # the appropriate keymap folder that will get included automatically
@ -30,4 +31,3 @@ BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight. RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight.
API_SYSEX_ENABLE = no API_SYSEX_ENABLE = no
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend

View file

@ -1,63 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #

View file

@ -1,10 +1,14 @@
# MCU name
MCU = atmega32u4 MCU = atmega32u4
F_CPU = 16000000
ARCH = AVR8
F_USB = $(F_CPU)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
# ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
NKRO_ENABLE = yes NKRO_ENABLE = yes

View file

@ -1,53 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Bootloader
# This definition is optional, and if your keyboard supports multiple bootloaders of
# different sizes, comment this out, and the correct address will be loaded
# automatically (+60). See bootloader.mk for all options.
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# comment out to disable the options. # comment out to disable the options.
# #

View file

@ -1,3 +1,5 @@
BLUETOOTH_ENABLE = yes # Processor frequency
F_CPU = 8000000 F_CPU = 8000000
BLUETOOTH_ENABLE = yes
BLUETOOTH = AdafruitBLE BLUETOOTH = AdafruitBLE

View file

@ -1,14 +1 @@
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
BLUETOOTH_ENABLE = no BLUETOOTH_ENABLE = no

View file

@ -1,44 +1,14 @@
SRC += matrix.c TWIlib.c issi.c lighting.c
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Bootloader
# This definition is optional, and if your keyboard supports multiple bootloaders of
# different sizes, comment this out, and the correct address will be loaded
# automatically (+60). See bootloader.mk for all options.
BOOTLOADER = caterina
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
# Build Options # Build Options
@ -72,6 +42,7 @@ CUSTOM_MATRIX = yes
#ifeq ($(strip $(WATCHDOG_ENABLE)), yes) #ifeq ($(strip $(WATCHDOG_ENABLE)), yes)
# TMK_COMMON_DEFS += -DWATCHDOG_ENABLE # TMK_COMMON_DEFS += -DWATCHDOG_ENABLE
#endif #endif
SRC += matrix.c TWIlib.c issi.c lighting.c
DEFAULT_FOLDER = meira/promicro DEFAULT_FOLDER = meira/promicro
LAYOUTS = ortho_4x12 LAYOUTS = ortho_4x12

View file

@ -1,51 +1,15 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to BOOTLOADER = caterina
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable

View file

@ -1,63 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #

View file

@ -1,47 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
OPT_DEFS += -DBOOTLOADER_SIZE=4096
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# Build Options # Build Options
# comment out to disable the options. # comment out to disable the options.
# #

View file

@ -1,63 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #

View file

@ -1,2 +1 @@
RGBLIGHT_ENABLE = yes # Enable keyboard RGB underglow RGBLIGHT_ENABLE = yes

View file

@ -1,63 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #
@ -82,4 +35,3 @@ HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400)
DEBUG_ENABLE = no DEBUG_ENABLE = no
CUSTOM_MATRIX = no # Use custom matrix code CUSTOM_MATRIX = no # Use custom matrix code
SPLIT_KEYBOARD = yes # Use shared split_common code SPLIT_KEYBOARD = yes # Use shared split_common code

View file

@ -1 +1 @@
BACKLIGHT_ENABLE = no BACKLIGHT_ENABLE = no

View file

@ -1,52 +1,16 @@
SRC += matrix.c \
i2c.c \
split_util.c \
serial.c
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Bootloader
# This definition is optional, and if your keyboard supports multiple bootloaders of
# different sizes, comment this out, and the correct address will be loaded
# automatically (+60). See bootloader.mk for all options.
BOOTLOADER = caterina BOOTLOADER = caterina
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Build Options # Build Options
# change to "no" to disable the options, or define them in the Makefile in # change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically # the appropriate keymap folder that will get included automatically
@ -68,5 +32,9 @@ USE_I2C ?= no
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
CUSTOM_MATRIX = yes CUSTOM_MATRIX = yes
SRC += matrix.c \
i2c.c \
split_util.c \
serial.c
DEFAULT_FOLDER = minidox/rev1 DEFAULT_FOLDER = minidox/rev1

View file

@ -1,56 +1,15 @@
SRC += i2c.c \
serial.c \
matrix.c \
split_util.c \
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to BOOTLOADER = caterina
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
@ -73,5 +32,9 @@ FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches
HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400)
CUSTOM_MATRIX = yes CUSTOM_MATRIX = yes
SRC += i2c.c \
serial.c \
matrix.c \
split_util.c
USE_I2C = yes USE_I2C = yes
RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight. RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight.

View file

@ -1,56 +1,16 @@
OPT_DEFS += -DMITOSIS_PROMICRO
MITOSIS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \
avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB)
# # project specific files
SRC = matrix.c
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Bootloader
# This definition is optional, and if your keyboard supports multiple bootloaders of
# different sizes, comment this out, and the correct address will be loaded
# automatically (+60). See bootloader.mk for all options.
BOOTLOADER = caterina BOOTLOADER = caterina
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Build Options # Build Options
# comment out to disable the options. # comment out to disable the options.
# #
@ -72,3 +32,10 @@ USB = /dev/ttyACM0
# upload: build # upload: build
# $(MITOSIS_UPLOAD_COMMAND) # $(MITOSIS_UPLOAD_COMMAND)
OPT_DEFS += -DMITOSIS_PROMICRO
MITOSIS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \
avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB)
# # project specific files
SRC = matrix.c

View file

@ -1,18 +0,0 @@
# Build Options
# change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically
#
BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = no # Console for debug(+400)
COMMAND_ENABLE = yes # Commands for debug and configuration
NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality
MIDI_ENABLE = no # MIDI controls
AUDIO_ENABLE = no # Audio output on port C6
UNICODE_ENABLE = no # Unicode
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight.
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend

View file

@ -1,51 +1,15 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to BOOTLOADER = atmel-dfu
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
@ -53,14 +17,15 @@ OPT_DEFS += -DBOOTLOADER_SIZE=4096
BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes # Mouse keys(+4700) MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450) EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = yes # Console for debug(+400) CONSOLE_ENABLE = no # Console for debug(+400)
COMMAND_ENABLE = yes # Commands for debug and configuration COMMAND_ENABLE = yes # Commands for debug and configuration
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work # if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
NKRO_ENABLE = no # USB Nkey Rollover NKRO_ENABLE = yes # USB Nkey Rollover
BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default
MIDI_ENABLE = no # MIDI controls MIDI_ENABLE = no # MIDI controls
UNICODE_ENABLE = no # Unicode UNICODE_ENABLE = no # Unicode
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE = no # Audio output on port C6 AUDIO_ENABLE = no # Audio output on port C6
RGBLIGHT_ENABLE = yes

View file

@ -1,2 +0,0 @@
# used by default keymap
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)

View file

@ -1,53 +1,21 @@
QUANTUM_LIB_SRC += i2c_master.c
SRC += leds.c \
matrix.c
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
BOOTLOADER = caterina BOOTLOADER = caterina
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #
BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = no # Mouse keys(+4700) MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450) EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = yes # Console for debug(+400) CONSOLE_ENABLE = yes # Console for debug(+400)
COMMAND_ENABLE = no # Commands for debug and configuration COMMAND_ENABLE = no # Commands for debug and configuration
@ -59,6 +27,9 @@ MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config)
UNICODE_ENABLE = no # Unicode UNICODE_ENABLE = no # Unicode
CUSTOM_MATRIX = yes CUSTOM_MATRIX = yes
QUANTUM_LIB_SRC += i2c_master.c
SRC += leds.c \
matrix.c
# You can set RGB_MATRIX_ENABLE = no in your rules.mk to disable this and save the Flash # You can set RGB_MATRIX_ENABLE = no in your rules.mk to disable this and save the Flash
RGB_MATRIX_ENABLE = custom # Enable RGB matrix effects (+10000). RGB_MATRIX_ENABLE = custom # Enable RGB matrix effects (+10000).

View file

@ -1,50 +1,14 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# Build Options # Build Options

View file

@ -1,47 +1,19 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# Build Options # Build Options
# comment out to disable the options. # comment out to disable the options.
# #
BOOTMAGIC_ENABLE = lite # Virtual DIP switch configuration(+1000) BOOTMAGIC_ENABLE = lite # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = no # Mouse keys(+4700) MOUSEKEY_ENABLE = no # Mouse keys(+4700)
EXTRAKEY_ENABLE = no # Audio control and System control(+450) EXTRAKEY_ENABLE = no # Audio control and System control(+450)

View file

@ -1,51 +1,15 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to BOOTLOADER = atmel-dfu
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable