1
0
Fork 0
qmk_firmware/lib/usbhost/USB_Host_Shield_2.0/cdcprolific.h

159 lines
6.5 KiB
C++

/* Copyright (C) 2011 Circuits At Home, LTD. All rights reserved.
This software may be distributed and modified under the terms of the GNU
General Public License version 2 (GPL2) as published by the Free Software
Foundation and appearing in the file GPL2.TXT included in the packaging of
this file. Please note that GPL2 Section 2[b] requires that all works based
on this software must also be made publicly available under the terms of
the GPL2 ("Copyleft").
Contact information
-------------------
Circuits At Home, LTD
Web : http://www.circuitsathome.com
e-mail : support@circuitsathome.com
*/
#if !defined(__CDCPROLIFIC_H__)
#define __CDCPROLIFIC_H__
#include "cdcacm.h"
//#define PL2303_COMPAT // Uncomment it if you have compatibility problems
#define PL_VID 0x067B
#define CHECK_PID(pid) ( pid != 0x2303 && pid != 0x0609 )
//#define PL_PID 0x0609
#define PROLIFIC_REV_H 0x0202
#define PROLIFIC_REV_X 0x0300
#define PROLIFIC_REV_HX_CHIP_D 0x0400
#define PROLIFIC_REV_1 0x0001
#define kXOnChar '\x11'
#define kXOffChar '\x13'
#define SPECIAL_SHIFT (5)
#define SPECIAL_MASK ((1<<SPECIAL_SHIFT) - 1)
#define STATE_ALL ( PD_RS232_S_MASK | PD_S_MASK )
#define FLOW_RX_AUTO ( PD_RS232_A_RFR | PD_RS232_A_DTR | PD_RS232_A_RXO )
#define FLOW_TX_AUTO ( PD_RS232_A_CTS | PD_RS232_A_DSR | PD_RS232_A_TXO | PD_RS232_A_DCD )
#define CAN_BE_AUTO ( FLOW_RX_AUTO | FLOW_TX_AUTO )
#define CAN_NOTIFY ( PD_RS232_N_MASK )
#define EXTERNAL_MASK ( PD_S_MASK | (PD_RS232_S_MASK & ~PD_RS232_S_LOOP) )
#define INTERNAL_DELAY ( PD_RS232_S_LOOP )
#define DEFAULT_AUTO ( PD_RS232_A_DTR | PD_RS232_A_RFR | PD_RS232_A_CTS | PD_RS232_A_DSR )
#define DEFAULT_NOTIFY 0x00
#define DEFAULT_STATE ( PD_S_TX_ENABLE | PD_S_RX_ENABLE | PD_RS232_A_TXO | PD_RS232_A_RXO )
#define CONTINUE_SEND 1
#define PAUSE_SEND 2
#define kRxAutoFlow ((UInt32)( PD_RS232_A_RFR | PD_RS232_A_DTR | PD_RS232_A_RXO ))
#define kTxAutoFlow ((UInt32)( PD_RS232_A_CTS | PD_RS232_A_DSR | PD_RS232_A_TXO | PD_RS232_A_DCD ))
#define kControl_StateMask ((UInt32)( PD_RS232_S_CTS | PD_RS232_S_DSR | PD_RS232_S_CAR | PD_RS232_S_RI ))
#define kRxQueueState ((UInt32)( PD_S_RXQ_EMPTY | PD_S_RXQ_LOW_WATER | PD_S_RXQ_HIGH_WATER | PD_S_RXQ_FULL ))
#define kTxQueueState ((UInt32)( PD_S_TXQ_EMPTY | PD_S_TXQ_LOW_WATER | PD_S_TXQ_HIGH_WATER | PD_S_TXQ_FULL ))
#define kCONTROL_DTR 0x01
#define kCONTROL_RTS 0x02
#define kStateTransientMask 0x74
#define kBreakError 0x04
#define kFrameError 0x10
#define kParityError 0x20
#define kOverrunError 0x40
#define kCTS 0x80
#define kDSR 0x02
#define kRI 0x08
#define kDCD 0x01
#define kHandshakeInMask ((UInt32)( PD_RS232_S_CTS | PD_RS232_S_DSR | PD_RS232_S_CAR | PD_RS232_S_RI ))
#define VENDOR_WRITE_REQUEST_TYPE 0x40
#define VENDOR_WRITE_REQUEST 0x01
#define VENDOR_READ_REQUEST_TYPE 0xc0
#define VENDOR_READ_REQUEST 0x01
// Device Configuration Registers (DCR0, DCR1, DCR2)
#define SET_DCR0 0x00
#define GET_DCR0 0x80
#define DCR0_INIT 0x01
#define DCR0_INIT_H 0x41
#define DCR0_INIT_X 0x61
#define SET_DCR1 0x01
#define GET_DCR1 0x81
#define DCR1_INIT_H 0x80
#define DCR1_INIT_X 0x00
#define SET_DCR2 0x02
#define GET_DCR2 0x82
#define DCR2_INIT_H 0x24
#define DCR2_INIT_X 0x44
// On-chip Data Buffers:
#define RESET_DOWNSTREAM_DATA_PIPE 0x08
#define RESET_UPSTREAM_DATA_PIPE 0x09
#define PL_MAX_ENDPOINTS 4
enum tXO_State {
kXOnSent = -2,
kXOffSent = -1,
kXO_Idle = 0,
kXOffNeeded = 1,
kXOnNeeded = 2
};
enum pl2303_type {
unknown,
type_0, /* don't know the difference between type 0 and */
type_1, /* type 1, until someone from prolific tells us... */
rev_X,
rev_HX, /* HX version of the pl2303 chip */
rev_H
};
class PL2303 : public ACM {
uint16_t wPLType; // Type of chip
public:
PL2303(USB *pusb, CDCAsyncOper *pasync);
// USBDeviceConfig implementation
uint8_t Init(uint8_t parent, uint8_t port, bool lowspeed);
//virtual uint8_t Release();
//virtual uint8_t Poll();
//virtual uint8_t GetAddress() { return bAddress; };
//// UsbConfigXtracter implementation
//virtual void EndpointXtract(uint8_t conf, uint8_t iface, uint8_t alt, uint8_t proto, const USB_ENDPOINT_DESCRIPTOR *ep);
#ifdef PL2303_COMPAT
private:
/* Prolific proprietary requests */
uint8_t vendorRead( uint8_t val_lo, uint8_t val_hi, uint16_t index, uint8_t* buf );
uint8_t vendorWrite( uint8_t val_lo, uint8_t val_hi, uint8_t index );
#endif
};
#ifdef PL2303_COMPAT
/* vendor read request */
inline uint8_t PL2303::vendorRead( uint8_t val_lo, uint8_t val_hi, uint16_t index, uint8_t* buf )
{
return( pUsb->ctrlReq(bAddress, 0, VENDOR_READ_REQUEST_TYPE, VENDOR_READ_REQUEST, val_lo, val_hi, index, 1, 1, buf, NULL ));
}
/* vendor write request */
inline uint8_t PL2303::vendorWrite( uint8_t val_lo, uint8_t val_hi, uint8_t index )
{
return( pUsb->ctrlReq(bAddress, 0, VENDOR_WRITE_REQUEST_TYPE, VENDOR_WRITE_REQUEST, val_lo, val_hi, index, 0, 0, NULL, NULL ));
}
#endif
#endif // __CDCPROLIFIC_H__